Pioneer AVH-X390BS, Owner'S Manual

Page: 42 / 204

42
p
This function is not available while you make or receive a call
using the hands-free function.
1 Display the “ Audio ” setting screen.
 Refer to Displaying the “ Audio ” setting screen on page 41
2 Touch [ Loudness ].
3 Touch the item.
The following items are available:
Off
,
Low
,
Mid
,
High
.
Setting the subwoofer output
This product is equipped with a subwoofer output mechanism,
which can be turned on or off.
The default setting is “ On ”.
1 Display the “ Audio ” setting screen.

Refer to Displaying the “ Audio ” setting screen on page 41
2 Touch [
Subwoofer
] to switch “
On
” or “
Off
”.
Adjusting the cutoff frequency
value
You can adjust the cutoff frequency value of each speaker.
The following speakers can be adjusted:
Standard Mode : Front, Rear, Subwoofer.
Network Mode : High, Mid, Subwoofer.
p
“ Subwoofer Settings ” is available only when “ Subwoofer ”
is “ On ”.
 Refer to Setting the subwoofer output on page 42
1 Display the “ Audio ” setting screen.
 Refer to Displaying the “ Audio ” setting screen on page 41
2 Touch [ Crossover ] or [ Subwoofer Settings ].
3 Touch or to switch the speaker.
4 Drag the graph line to set the cutoff position.
5 Drag the lowest point of the graph to set the
cutoff slope.
p
The following items can also be set.

⁂⁚⁓⁥⁗
:
Switches the subwoofer phase between normal and reverse
position.

LPF
/
HPF
:
Switches the LPF / HPF setting to “ On ” or “ Off ”.
When it is turned off, the high-pass filter or low-pass filter of
each speaker can also be turned on by touching the graph
lines.
p
This function is not available when adjusting the High
speaker.
Switching the rear speaker
output
p
This function is available when “
Standard Mode
” is selected
as the speaker mode.
The default setting is “
Rear
”.
1 Turn the source off.
 Refer to Selecting a source on page 11
2 Display the “ Audio ” setting screen.
 Refer to Displaying the “ Audio ” setting screen on page 41
3 Touch [ Rear Speaker Output ].
4 Touch to switch “ Rear ” or “ Subwoofer ”.
Using BASS Boost
1 Display the “ Audio ” setting screen.
 Refer to Displaying the “ Audio ” setting screen on page 41
2 Touch [ BASS Boost ].
3 Touch to select the bass boost level from 0 to
+6 .
Selecting the listening position
You can select a listening position that you want to make as the
center of sound effects.
The default setting is “ Off ”.
1 Display the “ Audio ” setting screen.
 Refer to Displaying the “ Audio ” setting screen on page 41
2 Touch [ Listening Position ].
3 Touch the desired position to change the lis-
tening position.
The following items are available:
Off
,
Front-L
,
Front-R
,
Front
,
All
.
p
“ All ” is not available when “ Network Mode ” is selected as
the speaker mode.
Adjusting the speaker output
levels finely
Fine adjustments of the speaker output level can be made by
listening to audio output.
p
This function is available when “
Subwoofer
” is set to “
On
”.
 Refer to Setting the subwoofer output on page 42
1 Display the “ Audio ” setting screen.

Refer to Displaying the “ Audio ” setting screen on page 41
2 Touch [
Speaker Level
].
3 Touch or to select the listening position
if necessary.
The following items are available:
Off , Front-L , Front-R , Front , All .
p
The default setting is “ Off ”.
p
“ All ” is not available when “ Network Mode ” is selected as
the speaker mode.
p
If you change the listening position setting, the output
levels of all the speakers will change in conjunction with the
setting.
4 Touch or to adjust the speaker output
level.
p
“ –24 ” dB to “ 10 ” dB is displayed as the level to be corrected
is increased or decreased.
The following speakers are available:
Standard Mode
: Front Left, Front Right, Rear Left, Rear Right,
Subwoofer
Network Mode
: High Left, High Right, Mid Left, Mid Right,
Subwoofer
p
To use this function, the vehicle’s acoustics must be mea-
sured in advance.
Adjusting the time alignment
By adjusting the distance from each speaker to the listening
position, time alignment is able to correct the time required for
sound to reach the listening position.
1 Measure the distance between the head of the
listener and each speaker unit.
2 Display the “
Audio
” setting screen.
 Refer to Displaying the “
Audio
” setting screen on page 41
3 Touch [ Time Alignment ].
4 Touch or to select the listening position
if necessary.
The following items are available:
< QRD3482-A >
Audio adjustments