PIONEER DJ SERATO DDJ-REV7 Instruction Manual Download

Page: 79 / 118

External input

If you connect a DJ player or turntable to the external input terminals on the unit, you can mix
the sounds of the external inputs without using a PC/Mac.

Mixing sounds of external inputs

1 Connect an external device to the [CH 1] or [CH 2] terminals.

2 Set the [LINE/PHONO] selector switch to [LINE] or [PHONO].

•

Set to [

LINE

] when you connect a line-level output device such as a DJ player.

•

Set to [

PHONO

] when you connect a phono-level (MM cartridge) output device such

as a turntable.

3 Set the input selector switch to [PHONO/LINE].

4 Turn the [TRIM] knob to adjust the input sound volume.

5 Move the channel fader to adjust the output sound volume.

Summary of Contents for SERATO DDJ-REV7























































































































Search results

Summary of Contents for SERATO DDJ-REV7

Reviews:

Related manuals for SERATO DDJ-REV7

Brands by name

Popular brands

PIONEER DJ SERATO DDJ-REV7, Instruction Manual

Search results

Summary of Contents for SERATO DDJ-REV7

Reviews:

Related manuals for SERATO DDJ-REV7

Brands by name

Popular brands