PIONEER DJ SERATO DDJ-REV7 Instruction Manual Download

Page: 31 / 118

Connections (basic styles)

Turn the unit off and disconnect the power cord before connecting other units.
Connect the power cord after all the connections are complete.

•

Use the supplied AC adapter and power cord.

•

Read the instruction manuals for the devices you are going to connect with the unit.

•

Connect the unit directly to your PC/Mac with the supplied USB cable or a USB cable that
conforms to USB 2.0 standards (do not use a USB hub).

Connecting to the input terminals

•

Set the [

LINE/PHONO

] selector switches for the [

CH 1

] and [

CH 2

] terminals to [

PHONO

]

when you connect a turntable to the terminals, and to [

LINE

] when you connect a DJ player

to the terminals.

R L

PC/Mac

AC adapter

To power outlet

Rear panel of the unit

DJ player

Power cord

Turntable

DJ player

Portable
audio device

Turntable

DJ player

Microphone

Summary of Contents for SERATO DDJ-REV7























































































































Search results

Summary of Contents for SERATO DDJ-REV7

Reviews:

Related manuals for SERATO DDJ-REV7

Brands by name

Popular brands

PIONEER DJ SERATO DDJ-REV7, Instruction Manual

Search results

Summary of Contents for SERATO DDJ-REV7

Reviews:

Related manuals for SERATO DDJ-REV7

Brands by name

Popular brands