Pingtek PT-255, Original Instructions Manual, Page: 15 / 15

●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●Mount the saw on a piece 18 mm thick
MDF or Plywood board (800 x 500 min
●It may be necessary to countersink any
●Use ‘G’ clamps or similar to clamp the
●Never place your hands within the ‘no
●The work-piece must be firmly secured to
●Use the Hold Down clamp to secure the
●Do not attempt ‘awkward’ operations
●Before attempting a cut, make a ‘dry run’
●Keep your hands in position until the
●DO NOT OVER-REACH.
●Keep good footing and balance. Stand to
●
●Gently press down on the Cutting Handle.
●Pull out the Cutting Head Latching Pin
●Gently rock the Cutting Head up and
●At the same time twist the Head Latching
●Press the switch to start the motor.
●Release the switch to turn off the motor.
speeds. Refer to ‘SELECTING THE
●Slide the Cutting Head to the rear as far as
●Tighten the Sliding Carriage Locking
●Place the work-piece on the table and
●Grasp the Cutting Head ‘D’ handle.
●Turn the motor on by squeezing the trigger
●Operate the lower guard locking/release
●Lower the Cutting Handle downwards and
●Allow the speed of the blade to do the
●When the cut has been completed,
●Allow the Cutting Head to rise to its upper
●Only remove the work-piece when the
●Position the work-piece on the table and
●Loosen the Sliding Carriage Locking
●Grasp the Cutting Handle and pull the
●Operate the ON/OFF motor trigger switch
●Operate the lower blade guard locking
●Push the Cutting Handle all the way down
●Gently push the Cutting Handle rearwards
●Always push the Cutting Head to the full
●Loosen the Mitre Locking Handle
●Pull up the Positive Stop Locking Lever.
●Turn the rotary table to the desired angle.
●Tighten the Mitre Locking Handle when
●Loosen the socket headed screw.
●Slide the upper section of the Fence
●Conduct a ‘dry run’ with the power off to
●Loosen the Bevel Locking Handle.
●Tilt the Cutting Head to the desired angle.
●Ensure the handle is tightened securely
●Select the required Mitre angle as
CUTTING.
●Select the required Bevel angle as
CUTTING.
●Ensure the tightness of all locking screws
●Turn machine “OFF” by releasing the
●Allow the blade to come to a complete
●Unplug the machine from the mains
●Carefully remove any jammed material
●Check the condition and operation of the
●Check for any other damage to any part of
●Have any damaged parts replaced by a
●Loosen the knurled locking nut.
●Adjust the depth stop screw to limit the
●Once set to the desired depth, tighten the
●When cutting is complete, return the depth
●Ensure the Cutting Head is in the upper
●Operate the lower guard locking/release
●Rotate the lower guard up and into the
●Press the arbor lock button to lock the
●Using the supplied Hex Key release the
.
●Install the outer blade flange, washer and
●Ensure the Hex Key is removed and the
●Loosen the Repeat Stop thumb screws
●Position the Repeat Stop approximately half way
●Attach the Workpiece Support Bar to the
●Remove the six (6) cross-head screws that
●Lift the insert from the table.
●Remove any debris that may have accumulated
●Fit the replacement insert, and replace the six
●Check that all of the fixing screws are tightened
exist. Check with your relevant Government
UK TECHNICAL/SERVICE
Tel: 01484 443541