Pima CLV412, Installation Instructions Manual

Page: 2 / 8

-2-
 Audio
o
Digital Audio and VoLTE (Voice
over LTE; Optional)
 Interfaces
o
USB 2.0
o
6-pin connector
o
Antennas
 Enhanced Features
o
DFOTA: Delta Firmware Over the
Air

Electrical Characteristics
o
Output Power:
 Class 3 (23dBm±2dB) for LTE
FDD
 Class 3 (23dBm±2dB) for LTE
TDD
 Class 3 (24dBm+1/-3dB) for
WCDMA
 Class E2 (27dBm±3dB) for EDGE
850/900MHz

Class E2 (26dBm+3/-4dB) for
EDGE
 1800/1900MHz
 Class 4 (33dBm±2dB) for GSM
850/900MHz
 Class 1 (30dBm±2dB) for GSM
1800/1900MHz
o
Consumption:
 20uA @Power off
 3mA @Sleep, Typ.
 22mA @Idle
o
Sensitivity:
 LTE B1: -101.5dBm (10M)
 LTE B2: -101dBm (10M)
 LTE B3: -101.5dBm (10M)
 LTE B4: -101dBm (10M)
 LTE B5: -101dBm (10M)
 LTE B7: -99.5dBm (10M)
 LTE B8: -101dBm (10M)

LTE B12: -101dBm (10M)
 LTE B13: -100dBm (10M)

LTE B20: -102.5dBm (10M)
 LTE B28: -102dBm (10M)
 WCDMA B1: -110dBm
 WCDMA B2: -110dBm
 WCDMA B4: -110dBm
 WCDMA B5: -110.5dBm
 WCDMA B8: -110.5dBm
 GSM: -109dBm
 DCS: -109dBm
 Approvals
o
RoHS Compliant
o
CE/GCF/Vodafone (Europe)
o
Anatel (Brazil)
Content of the product package
 CLV412 Add-on  Antenna  This guide
How to install the CLV412
Disconnect the control panel from AC and remove the batteries before installing the CLV412.
Follow the next steps to install the add-on.
1.
Make sure the
VISION
is located away from other transmitting devices, or near large metal objects.
2. Carefully pull out the SIM card tray (no. 3 in the above figure) from the socket, by gently pressing the eject bar (no. 7 in the figure).
3.
Align
(U)SIM1 (Main) card into slot 8, and (U)SIM2 (Backup) card into slot 9, with the metal contacts facing downwards and the
angled corner of the card positioned correctly, and carefully insert the tray into place.
4. Connect the antenna to the antenna connector (no. 10 in the figure).
5. Connect the add-on’s circuit board connector (no. 12 in the figure) to its socket on the control panel’s circuit board.
6. Connect the control panel to power.
7. Use an LCD keypad (not supplied) and set the add-on; see how in the Installation guide.
8. Test the add-on using the
Test and Diagnostics menu.
The LEDs
The CLV412 LEDs (no. 11 in the figure) are described in the table below.
Label Color and state Description
LD1
Yellow blinks (200ms on/1800ms off) Network search
Yellow blinks (1800ms on/200ms off) Idle
Yellow blinks (125ms on/125ms off) Data transfer
Yellow solid Voice call
LD2
Red solid Modem is registered on LTE network
Red off Modem is registered on other network
LD3 Green solid Power on
LD4 Blue Used by the manufacturer
Ordering information
 CLV412 Kit: P/N 8300069