manualshive.com logo in svg

Pilz PMI m309 diag, Operating Manual

Share
Download
Pilz PMI m309 diag Operating Manual Download Page 14

PMI m309 diag operating manual

3-4

Safety

•

Operation

- Plan the system correctly to ensure that a communication error

between the PMIvisu/PMIopen and the host computer does not cause a
malfunction.

- Do not operate the touchscreen interface using hard or heavy objects or

apply excessive pressure.

- The maximum ambient temperature must not be exceeded when using

the unit.

- Do not pour liquids over the unit or insert any objects into the unit.
- When in storage and during operation, protect the unit from vibration

and shock.

- Avoid using chemicals close to the unit.

•

Maintenance

Do not use thinners or organic solvents to clean the unit and
touchscreen interface.

NOTICE

The touchscreen interface is not abrasion-resistant; if it is dirty, please
clean with care and do not apply heavy pressure.

Further information on care and maintenance of the touchscreen can be
found in chapter 7.

Summary of Contents for PMI m309 diag












































Reviews:

No comments

Brands by name

Popular brands

Load more brands