Pilot Communications J-10 Jet 107

Introduction

Warrant

!

 All  Pilot-RC products are guaranteed against defects for 30 days of receiving your airplane. This 

warranty is limited to construction or production defects in both material and workmanship , it does 
not cover any component parts damaged through use or modification .

!

 The manufacture cannot supervise the assembly, operation or maintenance, and is not 

responsible for radio malfunctions. Please ensure  your  radio system is in good condition. 

We are 

not responsible for any accident or damage while using this product.

 It is impossible to determine 

for certain whether crash damage was the result of improper installation of our products, a radio 
system failure, or pilot error. Model airplane owners use our products at their own risk.

!

 Pilot-RC will not be liable for any costs, unless agreed and proved beyond doubt the failure was 

due to faulty materials or fabrication. Any agreed cost will not exceed the cost of the airframe and 
not include engine, radio equipment or third party claims.

!

 Should you wish to return a product or receive replacement parts, all shipping cost must be paid 

by the customer.

Attention

!

 1. 

Do not regard this plane as a toy!

!

 2. To ensure safety, please read the instruction manual thoroughly before assembly.

!

 3. Building and operating an RC Plane of this nature

requires previous experience and competence to an experienced level. This plane is not for a 
beginner!

!

 4. If you are in doubt have an experienced pilot at hand. Diligent practicing and correct guidance 

is essential, accidents can cause bodily harm and property damage.

!

 5. Seek assistance from an experienced person or airplane model clubs in assembly, operation 

and maintenance to ensure successful training.

!

 6. 

Fly only in a registered RC model club airfield

 that is approved by your local Academy of 

Model Aeronautics (AMA).

 
!

 Pilot-RC has the right to revise the plane, the instructions and the limited warranty without notice. 

If you have any problems and questions please contact Pilot –RC

Email: [email protected] , [email protected] 
Phone:+86 760 88781293
FAX: +86 760 88780293
Address: No.34, Chengnan Er Road , Zhongshan city, 528400, Guangdong Province, China

!

  Thank you for purchasing our 2.7m(107”) J-10 Jet plane. we strive to achieve a good quality 

quick build ARF aircraft .
It requires the least amount of assembly of any ARF kit to obtain the maximum performance.
 

!

  Both the design and manufacturing have been undertaken to the highest standards, using best 

quality hardware, covering, wood & glue during factory construction stage.
 

!

  By optimal weight and balance along with reliable construction, you will find this plane ideal for 

flying.
We hope that every effort and service we offer will, in turn, give you confidence using PILOT 
Models.
 

!

  Have a wonderful time flying your aircraft in a suitable safe space!

Summary of Contents for J-10 Jet 107"
























Reviews: