Pifco P28027 Safety & Instruction Manual Download Page 5

5

www.pifco.co

USING YOUR APPLIANCE

1.  Before first use, it is recommended to fully 

charge your Robo Vac. A full charge takes 
approximately 8 hours.

2.  Once your Robo Vac is charged, carry it 

and the docking station into the room you 
wish to clean. 

3.  Place the docking station against a wall, 

ensuring there is a clear path for the Robo 
Vac to reach it.

4.  As the Robo Vac moves around the 

room it may knock into things. Clear any 
breakables, such as vases or ornaments 
from the floor. 

5.  Set the Robo Vac down on the floor and 

turn on. 

6.  The Robo Vac will automatically return 

to the docking station once cleaning is 
complete.

7.  The Robo Vac has an anti bump 

navigation sensor fitted, and will right itself 
if it hits anything.

Note:

 If using on carpeted floor, check to see if 

there are any carpet lips over 1 cm. The Robo 
Vac cannot move over lips higher than 1 cm. 
You may need to lift your Robo Vac and move 
it over the lip.

Auto Stop:

The Robo Vac will automatically stop when it is 
picked up. When you place it back down it will 
continue cleaning.

Anti Falling Sensors:

The Robo Vac’s inbtelligent navigation system 
includes anti falling sensors. When place on a 
surface or stairs, the Robo Vac will not drive off 
of the surface/stairs or fall. 

Docking Station:

Important: 

1.  The docking station must be placed by 

a wall/solid surface in order for the Robo 
Vac to dock. Do not place in the centre of 
a room.  

2.  Make sure the docking station is against a 

clear, unobstructed wall.

3.  Ensure that there are no barriers or 

obstacles in front of the dock, or any 
debris that will block the Robo Vacs path 
to the docking station.

4.  You must ensure the Robo Vac is in close 

enough range to the docking station 
to self-dock. Do not place the docking 
station in a separate room to the Robo 
Vac, for example. 

5.  If the Robo Vac runs out of battery during 

use, you must take it to the dock yourself. 
Ensure that you have switched the Robo 
Vac off before returning to the dock. 

6.  If the Robo Vac and the docking station 

do not connect correctly when charging, 
the indicator light will flash blue.

Charging:

As well as charging at the docking station, 
you can also charge the Robo Vac using the 
supplied charging adaptor. The charger jack is 
located on the side of the Robo Vac, next to 
the power switch. It will take approximately 8 
hours for a full charge. The indicator light will 
flash red during charging. Once a full charge is 
reached, the indicator light will be steadily red. 

Summary of Contents for P28027









Reviews: