PICOTE DN100 Operating & Safety Manual Download Page 24

 24

 

 

WARRANTY POLICY AND PROCEDURE 

 

Limited Warranty:

 

Picote warrants to the original End User that the Product purchased by such End User  will operate in 

accordance  with  and  substantially  conform  to  their  published  specifications  when  shipped  or  otherwise 
delivered to the End User and for a period  of one (1) year,  except  electric motors for which the warranty 
period shall be six (6) months, provided, however, that Picote does not warrant any claim or damage under 
this 

 

Warranty if such claim or damage results from:

 

1.

 

Consumable parts or normal wear and tear resulting from use of the Products,

 

2.

 

Product overload or overheated motor,

 

 

3.

 

Regular periodic maintenance of Products,  

 

4.

 

Misuse, neglect, or improper installation or maintenance of the Products, or use of Products 

 

not for their intended purpose,

 

5.

 

Products  that  have  been  altered,  modified,  repaired,  opened  or  tampered  with  by  anyone 

 

other than Picote or an authorized Picote Service Centre, or unsuitable or unauthorized spare 

 

parts, accessories or third party products when using the Products or;

 

6.

 

the use of the Products not in compliance with their respective Documentation, user manuals, 

 

safety and maintenance instructions, and any usage restrictions contained therein, or

 

7.

 

accident, fire, power failure, power surge, or other hazard. 

 

 

Otherwise, the Products are sold AS IS. End User is responsible for using the Products within 

 

their specifications and instructions as contained in the Documentation.

 

EXCEPT  AS  SPECIFIED  IN  THIS  WARRANTY,  ALL  EXPRESS  OR  IMPLIED  CONDITIONS, 

REPRESENTATIONS, AND WARRANTIES INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OR 
CONDITION  OF  MERCHANTABILITY,  FITNESS  FOR  A  PARTICULAR  PURPOSE,  NONINFRINGEMENT, 
SATISFACTORY QUALITY OR  ARISING FROM A  COURSE  OF  DEALING, LAW, USAGE, OR  TRADE  PRACTICE, 
ARE  HEREBY  EXCLUDED  TO  THE  EXTENT  ALLOWED  BY  APPLICABLE  LAW.  TO  THE  EXTENT  AN  IMPLIED 
WARRANTY  CANNOT  BE  EXCLUDED,  SUCH  WARRANTY  IS  LIMITED  IN  DURATION  TO  THE  WARRANTY 
PERIOD.  BECAUSE  SOME  STATES  OR  JURISDICTIONS  DO  NOT  ALLOW  LIMITATIONS  ON  HOW  LONG  AN 
IMPLIED WARRANTY LASTS, THE ABOVE LIMITATION MAY NOT APPLY. This disclaimer and exclusion shall 
apply even if the express warranty set forth above fails of its essential purpose.

 

 

Summary of Contents for DN100


























Reviews: