background image

PCFM

7

Rev. 07/03

Ph: 800-421-6511

www.picomacom.com

Installation Procedure

It is recommended that assistance be available to safely install 
equipment in equipment racks. Chassis must be fastened 
securely in equipment rack before populating with modules.

1.

  Install chassis in equipment rack (equipment rack sold  

 

separately) by supporting the bottom and rear of PCFM  

 

at the desired elevation in rack. 

2.

  Line up the side holes of chassis with the tapped equipment  

 

rack holes.

3.

  Insert the provided screws through the side holes in chassis 

 

 and thread into the tapped equipment rack holes.

4.

  Fasten the bottom screws first, then fasten top screws  

 

(tighten securely).

5.

  Connect a cable from the left and the right output of the  

 

audio source to the left and right audio input connections  

 

of the PCFM. 

6.

  Connect a cable from the RF OUT connector of the PCFM  

 

and the input connector of combining system.

7.

  Connect power cord to receptacle supplying uninter- 

 

rupted line power (power LED on front panel will  

 illuminate).

8.

  Set the FM radio output channel by depressing the FREQ  

 

buttons repeatedly until the desired channel is displayed on  

 

front panel.

9.

 Connect a cable between the combining system test  

 

point and a spectrum analyzer or signal level meter.  

 

Measure the aural carrier level of the PCFM and a 

 

djacent channels. 

10.

 Adjust the Output level of the PCFM to 7 to 12dB below  

 

adjacent channel video carrier levels by adjusting the  

 

RF OUTPUT adjustment on the front panel of the  

 PCFM.

RF OUT

120VAC

60Hz 10W

AUDIO IN

600W MAX

L

R

!

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

_

+

_

+

_

+

_

+

+

+

+

+

VIDEO

OUT

COMPOSITE

OUT

70 MHz

IN

OUT

AUDIO OUTPUT LEVEL

VIDEO

LEVEL

RF IN

950-1450

MHz

18V 250mA

LNB POWER

OUT

ON     OFF

117V

.35A

60Hz

DATA

CLOCK

LANGUAGE

GND

+

_

MONO

LEFT

RIGHT

AUDIO OUTPUT

FUSE

AC25OV

1/2A

H

V

L

R

MONO

INV

NOR

STEREO AUDIO CONNECTION:

Center Conductor to Left + (Positive)

Shield to Left - (Negative)

Center Conductor to Right + (Positive)

Shield to Right - (Negative)

FROM SATELLITE ANTENNA

950-1750MHz

PCFM MODULATOR

PR4200IRD SATELLITE RECEIVER

RF OUT to Distribution System

RIGHT AUDIO IN

LEFT AUDIO IN

Summary of Contents for PCFM









Reviews: