Phoenix Model Laser L476S Instruction Manual Download Page 11

Page: 11 / 16

I/C FLIGHT GUIDELINES

When ready to fly, first extend the

transmitter aerial.

Operate the control sticks on the

transmitter and check that the control

surfaces move freely and in the

CORRECT directions.

ALWAYS land the model INTO the

wind, this ensures that the model lands

at the slowest possible speed.

Switch on the transmitter.

Switch off the transmitter.

Check that the transmitter batteries

have adequate power.

Switch off the receiver.

Switch on the receiver.

ALWAYS take off into the wind.

Check that the wings are correctly

fitted to the fuselage.

If the model does not respond correctly

to the controls, land it as soon as

possible and correct the fault.

Empty the fuel tank after flying, fuel left

in the tank can cause corrosion and

lead to engine problems.

I/C FLIGHT WARNINGS

Always operate in open areas, away

from factories, hospitals, schools,

buildings and houses etc. NEVER fly

your aircraft close to people or built

up areas.

THE PROPELLER IS DANGEROUS

Keep fingers, clothing (ties, shirt

sleeves, scarves) or any other loose

objects that could be caught or drawn

in, away from the propeller. Take care

at ALL times.

Keep all onlookers (especially small

children and animals) well back from

the area of operation. This is a flying

aircraft, which will cause serious

injury in case of impact with a person

or animal.

NEVER fly near power lines, aerials

or other dangerous areas including

airports, motorways etc.

NEVER use damaged or deformed

propellers or spinners.

DO NOT dispose of empty fuel

containers on a fire, this can lead to

an explosion.

NEVER fly in wet conditions or on

windy or stormy days.

ALWAYS adjust the engine from

behind the propeller, and do not allow

any part of your body to be in line

with the propeller.

TOOLS AND SUPPLIES NEEDED.

• Medium C/A glue.
• 30 minute epoxy.
• 6 minute epoxy.
• Hand or electric drill.
• Assorted drill bits.
• Modeling knife.
• Straight edge ruler.
• 2 bender plier.
• Wire cutters.
• Masking tape.
• Thread lock.
• Paper towels.
• Rubbing alcohol

SUGGESTION

To  avoid  scratching    your  new  airplane,  do  not
unwrap  the  pieces  until  they  are  needed  for
assembly. Cover your workbench with an old towel or
brown  paper,  both  to  protect  the  aircraft  and  to
protect  the  table.  Keep  a  couple  of  jars  or  bowls
handy to hold the small parts after you open the bag.

NOTE:

Please trial fit all the parts. Make sure you have the
correct parts and that they fit and are aligned properly
before gluing! This will assure proper assembly. The
YAK  54 ARF  is  hand  made  from  natural  materials,
every  plane  is  unique  and  minor  adjustments  may
have  to  be  made.  However,  you  should  find  the  fit
superior and assembly simple.

The painted and plastic parts used in this kit are fuel
proof. However, they are not tolerant of many harsh
chemicals including the following: paint thinner, C/A
glue accelerator, C/A glue debonder and acetone. Do
not let these chemicals come in contact with the
colors on the covering and the plastic parts.

SAFETY PRECAUTION:

• This is not a toy
• Be sure that no other flyers are using your radio

frequency.

• Do not smoke near fuel
• Store fuel in a cool, dry place, away from

children and pets.

• Wear safety glasses.
• The glow plug clip must be securely attached to

the glow plug.

• Do not flip the propeller with your fingers.
• Keep loose clothing and wires away from the propeller.
• Do not start the engine if people are near. Do not

stand in line with the side of the propeller.

• Make engine adjustments from behind the propeller

only. Do not reach around the spinning propeller.

INSTALLING THE AILERON SERVOS

1. Install the rubber grommets and brass eyelets

onto the aileron servo.

2. Turn the wing panel right side up. Using a

modeling knife, remove the covering from over
the precut servo box.

3. Connect a 150-200mm servo extension to each

aileron servo and prepare the thread as shown
in the picture below.

4. Using the thread as a guide and using masking

tape,  tape  the  servo  lead  to  the  end  of  the
thread: carefully pull the thread out. When you
have  pulled  the  servo  lead  out,  remove  the
masking  tape  and  the  servo  lead  from  the
thread.

Remove the
covering

Wingspan : 1425 mm (56.1 in)

Length : 1320 mm (51.97 in)

Weight : 2500g - 2700g

Engine : 40 - 46 two stroke or 52 four stroke

Radio

: 4 channel / 5 servo

Instruction Manual

6. Place the aileron servo into the servo box.

Secure the servo in place using the mounting
screws provided.

7. Repeat step # 2 - # 6 to install the second

aileron servo in the opposite wing half.

INSTALLING THE CONTROL HORNS

1. One aileron control horn in positioned on each

aileron. Using a ruler and a pen, locate and
mark the location of the control horn. It should
be mounted on the bottom side of the aileron at
the leading edge, in line with the aileron
pushrod.

2. Drill two 3mm holes through the aileron using

the control horn as a guide and screw the
control horn in place.

5. Pull the servo lead out.

RIGHT

WRONG

3. Repeat step # 1 - # 2 to install the control horn

on the opposite aileron.

INSTALLING THE AILERON LINKAGES

1. Working with the aileron linkage for now,

thread one nylon clevis at least 14 turns onto
one of the 2mm x 180mm threaded wires.

2. Attach the clevis to the outer hole in the control

horn. Install a silicone tube on the clevis.

3. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a
2mm drill bit, enlarge the third hole out from the
center of the arm to accommodate the aileron
pushrod wire.

4. Plug the aileron servo into the receiver and

center the servo. Install the servo arm onto the
servo. The servo arm should be perpendicular
to the servo and point toward the middle of the
wing.

5. Center the aileron and hold it in place using a

couple of pieces of masking tape.

6. With the aileron and aileron servo centered,

carefully place a mark on the aileron pushrod
wire where it crosses the hole in the servo arm.

7. Using pliers, carefully make a 90 degree bend

down at the mark made. Cut off the excess wire,
leaving about 4mm beyond the bend.

Silicone Tube

8. Insert the 90 degree bend down through the hole in

the servo arm. Install one nylon snap keeper over
the wire to secure it to the arm. Install the servo
arm retaining screw and remove the masking tape
from the aileron.

9. Repeat step # 4 - # 11 to install the second aileron

linkage. After both linkages are completed, connect
both of the aileron servo leads using a Y-harness
you have purchased separately.

HORIZONTAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Horizontal stabilizer with Elevator halves.

1. Using a modeling knife, cut away the covering

from the fuselage for the stabilizer and remove it.

INSTALLING THE WING TO THE FUSELAGE

Attach the wings to the joiner tube and using the
nylon thumbscrews to secure the wing panels to the
fuselage.

3. Check the fit of the horizontal stabilizer in its slot.

Make sure the horizontal stabilizer is square and
centered to the fuselage by taking measurements,
but don't glue anything yet.

4. With the horizontal stabilizer correctly aligned,

mark the shape of the fuselage on the top and
bottom of the tail plane using a water soluble /
non-permanent felt-tip pen.

5. Remove the stabilizer. Using the lines you just

drew as a guide, carefully remove the covering
from between them using a modeling knife.

When cutting through the covering to remove it,
cut with only enough pressure to only cut
through the covering it's self. Cutting into the
balsa structure may weaken it. This could lead to
possible failure during flight.

2. Draw a center line onto the horizontal stabilizer.

Draw a center line

6. When you are sure that everything is aligned

correctly, mix up a generous amount of 30 minute
epoxy. Apply a thin layer to the top and bottom of
the stabilizer mounting area and to the stabilizer
mounting platform sides in the fuselage. Slide the
stabilizer in place and re-align. Double check all
of your measurements one more time before the
epoxy cures. Remove any excess epoxy using a
paper towel and rubbing alcohol and hold the
stabilizer in place with T-pins or masking tape.

2. Slide the vertical stabilizer into the slot in the

mounting platform in the top of the fuselage. Mark
the shape of the fuselage on the left and right
sides of the vertical stabilizer using a felt-tip pen.

3. Now, remove the vertical stabilizer and using a

modeling knife, carefully cut just inside the marked
lines and remove the film on both sides of the
vertical stabilizer. Just as you did with the horizontal
stabilizer, make sure you only press hard enough to
cut the film, not the balsa vertical stabilizer.

4. Slide the vertical stabilizer back in place. Using a

triangle, check to ensure that the vertical stabilizer is
aligned 90 degree to the horizontal stabilizer.

5. When you are sure that everything is a aligned

correctly, mix up a generous amount of 30 minute
epoxy. Apply a thin layer to the slot in the mounting
platform and to the vertical stabilizer mounting
area. Apply epoxy to the lower rudder hinge. Set
the stabilizer in place and re-align. Double check
all of your measurements once more before the
epoxy cures. Remove any excess epoxy using a
paper towel and rubbing alcohol and hold the
stabilizer in place with T-pins or masking tape.
Allow the epoxy to fully cure before proceeding.

Glue with epoxy

Remove the covering

Glue with epoxy

Remove the covering

7. After the epoxy has fully cured, remove the

masking tape or T-pins used to hold the
stabilizer in place and carefully inspect the glue
joints. Use more epoxy to fill in any gaps that
were not filled previously and clean up the
excess using a paper towel and rubbing alcohol.

VERTICAL STABILIZER INSTALLATION

PARTS REQUIRED

· (1) Vertical stabilizer with rudder.
1. Using a modeling knife, remove the covering on
the top of the fuselage for the vertical stabilizer.

TAIL WHEEL INSTALLATION

PARTS REQUIRED

· (1) Tail wheel bracket w/wire.

· (1) Wheel collar with set screw.

· (1) 25mm diameter tail wheel.

· (2) nylon control clasp.

· (2) 2mm x 10mm screws.

· (2) 3mm x 12mm screws.

1. Set the tail wheel assembly in place on the

plywood plate.

2. Drill 2,6mm pilot holes through the plywood plate.

3. Secure the tail wheel bracket in place using two

3mm x 12mm screw.

4. Align the tail wheel wire so that the wire is parallel

with the bottom of the rudder. The control clasp
has a pre-drilled hole through the top of it. Slide
this hole on to the tail wheel wire while sliding the
clasp over the bottom of the rudder.

5. Secure the two clasps to the rudder bottom using

two 2mm x 10mm screws.

3. Using a modeling knife, carefully cut out two line

from the margin of the hole onto the wheel pant.

Just cut only one side of the wheel pant, where

the main gear will install. Be sure to make a left
and right wheel pant.

4. Slide a 4.5mm nut/ three 16mm flat washers /

4.5mm nut / collar / wheel / collar onto the axle.

5. Slide the axle assembly into the wheel pant.

There are just one nut and two flat washers

outside of the wheel pant.

6. Remove one nut, one flat washer. Attach the

main landing gear to the axle.

7. Center both collars and wheel in the middle of

the wheel pant, lock both collars in place using a
hexagon 2mm screw.

8. With the landing gear in place, tighten two nuts.

After installing the wheel pant, apply a small
drop of thin C/A to the bottom nut.

9. Repeat step # 1-8 to install the second wheel

pant assembly.

MAIN GEAR INSTALLATION

PARTS REQUIRED

· (2) Main gear.

· (2) 65mm diameter wheels.

· (2) Fiberglass wheel pants.

· (4) 6mm x 25mm machine screw.

· (4) 16mm flat washers

· (6) 16mm flat washers.

· (4) 4,5mm nut

· (4) Wheel c screws.

· (2) 4mm x 58mm axle.

INSTALLING THE WHEEL PANTS

1. Locate the wheel pants from the hardware bag.

Mark the locations of the mounting axles onto the
wheel pants. The locations of the two mounting
holes are the middle of the wheel opening, on right
side, left side and 10mm from the bottom of the
wheel pant.

2. Using a 5mm drill bit, carefully drill two pilot holes

through the wheel pant at the TWO marks you made.

Screw

drill

cut

10mm flat washer

Clasps

Screw

down thrust

right thrust

INSTALLING THE MAIN LANDING GEAR

1. Four nuts have been installed at the factory.
2. Install main landing gear into the fuselage using

(4) 6mm x 20mm machine screws and 10mm flat
washers provided in the kit.

ENGINE INSTALLATION

PARTS REQUIRED
• (4) 3mm x 25mm wood csrew
• (1) 1.3mm x 500mm wire.
• (1) 3.5mm x 350 mm nylon pushrod housing.
• (1) Metal connector.
• (1) Engine mount
• (4) 4mm x 25mm screw

INSTALLING THE ENGINE

1. Locate the long piece of wire used for the

throttle pushrod. One end of the wire has been
pre-bend in to a "Z" bend at the factory. This "Z"
bend should be inserted into the throttle arm of
the engine when the engine is fitted onto the
engine mount. Fit the engine to the engine
mount using the screws provided.

FUEL TANK

PARTS REQUIRED
·  (1) Nylon fuel tank.
·  (1) Metal clunk.
·  (1) Silicon tube.
·  (1) Pre-assemble stopper.
·  (1) 165mm x 250mm foam.

INSTALLING THE STOPPER ASSEMBLY

1. The stopper has been pre-assembled at the

factory.

2. Using a modeling knife, cut one length of silicon

fuel line (the length of silicon fuel line is
calculated by how the weighted clunk should
rest about 8mm away from the rear of the tank
and move freely inside the tank). Connect one
end of the line to the weighted clunk and the
other end to the nylon pick up tube in the
stopper.

3. Carefully bend the second nylon tube up at a 45

degree angle (using a cigarette lighter). This
tube will be the vent tube to the muffler.

4. Carefully bend the third nylon tube down at a 45

degree angle (using a cigarette lighter). This
tube will be vent tube to the fueling valve

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just
below the top surface of the tank. It should not
touch the top of the tank.

INSTALLING THE THROTTLE PUSHROD HOUSING

1. Install the engine mount into the fire wall using

4mm x 25mm screw.

2. Place the engine into the engine mount and

align it properly with the front of the cowling.
The distance from the firewall to the front of the
engine thrust washer should 110mm.

If your engine is equipped with a remote needle

valve, we suggest installing it into the engine at
this time.

3. When satisfied with the alignment of the engine,

use a pencil and mark the mounting hole location
onto the firewall, where the throttle pushrod will exit.

4. Now, remove the engine. Using a 5mm drill bit,

drill holes through the firewall and the forward
bulkhead at the marks made.

5. Slide the pushrod housing through the hole in

the firewall, through the hole in the forward
bulkhead, and into the servo compartment.

6. Apply a couple of drops of thin C/A to the pushrod

housing where it exits the firewall and where it

passes through the forward bulkhead. This will
secure the housing in place.

7. Using a modeling knife, cut off the nylon

pushrod housing 26mm in front of the servo tray.

5. Test fit the stopper assembly into the tank. It

may be necessary to remove some of the
flashing around the tank opening using a
modeling knife. If flashing is present, make sure
none of it falls into the tank.

6. When satisfied with the alignment of the stopper

assembly tighten the 3mm x 20mm machine
screw until the rubber stopper expands and
seals the tank opening. Do not over tighten the
assembly as this could cause the tank to split.

7. Using a modeling knife, cut 3 lengths of fuel line

150mm long. Connect 2 lines to the 2 vent tubes
and 1 line to the fuel pickup tube in the stopper.

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole in
the firewall. Pull the lines out from behind the
engine, while guiding the fuel tank into place.
Push the fuel tank as far forward as possible, the
front of the tank should just about touch the back
of the firewall.

Blow through one of the lines to ensure the fuel

lines have not become kinked inside the fuel
tank compartment. Air should flow through
easily.

Do not secure the tank into place permanently

until after balancing the airplane. You may need
to remove the tank to mount the battery in the
fuel tank compartment.

9. To secure the fuel tank in place, apply a bead of

silicon sealer to the forward area of the tank,
where it exits the fuselage behind the engine
mounting box and to the rear of the tank at the
forward bulkhead.

10. Secure the fuel tank using two rubber bands as

shown.

SERVO INSTALLATION
INSTALLING THE FUSELAGE SERVOS

1. Install the rubber grommets and brass collets

into the elevator, rudder and throttle servos. Test
fit the servos into the servo tray. Trim the tray if
necessary to fit your servos

2.Mount the servos to the tray using the mounting

screws provided with your radio system.

INSTALLING THE ELEVATOR PUSHROD

PARTS REQUIRED

·  (2) Wire pushrod.
·  (1) Domino connector
·  (2) Clevis
·  (2) Silicone tube
·  (1) Nylon snap keeper
·  (2) Nylon control horn w/plate
·  (4) 2mm x 14mm sheet metal screw
·  (2) Elevator pushrod

1. Locate the pushrod exit slot on the right side

and left side of the fuselage. It is located slightly
ahead and below the horizontal stabilizer.

2. Carefully cut away the covering material from

the slot.

3. Working from inside the fuselage, slide the

threaded end of the pushrod until it reaches the
exit slot. Carefully reach in with a small screw
driver and guide the pushrod out of the exit slot.

4. Install the clevis on the elevator pushrod. Make

sure 6mm of thread shows inside the clevis.

5. The control horn should be mounted on the

bottom, left side and right side of the elevator at
the leading edge, in line with the elevator
pushrod.

To carburator

To muffler

To vent Tube

6. Drill two 1,6mm holes through the elevator using

the control horn as a guide and screw the
control horn in place.

7. Attach clevis to the third hole in the control horn.

Install a silicone tube on the clevis.

8. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms. Using a
2mm drill bit, enlarge the third hole out from the
center to accommodate the elevator pushrod wire.

9. Plug the elevator servo into the receiver and

center the servo. Install the servo arm onto the
servo. The servo arm should be perpendicular
to the servo and point toward the middle of the
fuselage.

10. Be sure both elevator halves are flat. Center

both elevator halves and hold them in place
using a couple of pieces of masking tape.

11. Connect two elevator purshord to the metal

domino connector and secure it. Insert the wire
pushrod into the metal domino connector and
secure it.

12. With the elevator halves and elevator servo

centered, carefully place a mark on the elevator
pushrod wire where it crosses the hole in the
servo arm.

13. Using pliers, carefully make a 90 degree bend

up at the mark made. Cut off the excess wire,
leaving about 8mm beyond the bend.

14. Insert the 90 degree bend up through the hole in

the servo arm, install one nylon snap keeper
over the wire to secure it to the arm. Install the
servo arm retaining screw and remove the
masking tape the elevator halves.

15. Using thick CA glue, secure the pushrod

sleeves to the pushrod sleeve guide.

Control horn elevator

INSTALLING THE RUDDER PUSHROD

PARTS REQUIRED

·  (1) Clevis
·  (1) Nylon snap keeper.
·  (1) Silicone tube
·  (1) Nylon control horn W/plate.
·  (2) 2mm x 14mm machine screw
·  (1) Rudder pushrod.

1. Locate the pushrod exit slot on the left of the

fuselage.

2. Carefully cut away the covering material from

the slot.

3. Working from inside the fuselage, slide the

threaded end of the remaining pushrod down
the inside of the fuselage until the pushrod
reaches the exit slot. Carefully reach in with a
small screw driver and guide the pushrod out of
the exit slot.

4. Install the clevis on the rudder pushrod. Make

sure 6mm of thread shows inside the clevis.

5. The control horn should be mounted on the left

side of the rudder at the leading edge, in line
with the rudder pushrod.

6. Drill two 1,6mm holes through the rudder using

the control horn as a guide and screw the
control horn in place.

7. Attach clevis to the third hole in the control horn.

Install a silicone tube on the clevis.

8. Locate one nylon servo arm, and using wire

cutters, remove all but one of the arms using a
2mm drill bit, enlarge the third hole out from the
center to accommodate the rudder pushrod wire.

9. Plug the rudder servo into the receiver and

center the servo. Install the servo arm onto the
servo.

10. Center the rudder and hold it in place using a

piece of masking tape.

11. With the rudder and rudder servo centered,

carefully place a mark on the rudder pushrod
wire where it crosses the hole in the servo arm.

12. Using a pliers, carefully make a 90 degree

bend up at the mark made. Cut off excess
wire, leaving about 8mm beyond the bend.

13. Insert the 90 degree bend up through the hole

in the servo arm. Install one nylon snap keeper
over the wire to secure it to the arm. Install the
servo arm retaining screw and remove the
masking tape from the rudder.

14. Using thick CA glue, secure the pushrod

sleeves to the pushrod sleeve guide.

MOUNTING THE COWL

PARTS REQUIRED
· (1) fiberglass cowl
. (1) Wooden engine mount
· (4) 3mm x 12mm

1. Remove the muffler and needle valve assembly

from the engine. Slide the fiberglass cowl over
the engine.

2. Measure and mark the locations to be cut out for

engine head clearance, needle valve, muffler,.
Remove the cowl and make these cutouts using
a rotary tool with a cutting disc and a rotary
sanding drum attachment.

3. Slide the cowl back into place. Align the front of

the cowl with the crankshaft of the engine. The
front of the cowl should be positioned so the
crankshaft is in the middle of the precut opening.
Hold the cowl firmly in place using several
pieces of masking tape.

4. While holding the cowl firmly in position, drill four

1,6mm pilot holes through both the cowl and the

side edges of the firewall.

5. Using a 3mm drill bit, enlarge the four holes in

the cowling

Enlarging the holes through the cowl will prevent
the fiberglass from splitting when the mounting
screws are installed.

6. Glue the engine wooden to the cowl by epoxy.

7. Slide the cowl back over the engine and secure

it in place using four 3mm x 12mm wood
screws.

8. Install the muffler. Connect the fuel and pressure

lines to the carburator, muffler and fuel filler
valve. Tighten the screws completely.

INSTALLING THE THROTTLE

1. Install one adjustable metal connector through the

third hole out from the center of one servo arm,
enlarge the hole in the servo arm using a 2mm drill
bit to accommodate the servo connector. Remove
the excess material from the arm.

After installing the adjustable metal connector

apply a small drop of thin C/A to the bottom nut.
This will prevent the connector from loosening
during flight.

2. Plug the throttle servo into the receiver and turn

on the radio system. Check to ensure that the
throttle servo output shaft is moving in the
correct direction. When the throttle stick is
moved forward from idle to full throttle, the
throttle barrel should also open and close using
this motion. If not, reverse the direction of the
servo, using the transmitter.

3. Slide the adjustable metal connector / servo

arm assembly over the plain end of the pushrod
wire. Position the throttle stick and the throttle
trim at their lowest positions.

4. Manually push the carburator barrel fully closed.

Angle the arm back about 45 degree from center
and attach the servo arm onto the servo. With
the carburator barrel fully closed, tighte the set
screw in the adjustable metal connector.

5. Remove the excess throttle pushrod wire using wire

cutters and install the servo arm retaining screw.

AIR FRAME ASSEMBLIES

• (2) Wing halves with ailerons
• (1) Fuselage with canopy.
• (1) Horizontal stabilizer with elevator halves
• (1) Vertical stabilizer with rudder
• (1) Fiberglass cowling

MAIN GEAR ASSEMBLY

• (2) Main gear Aluminum
• (2) 60mm diameter wheels
• (2) Fiberglass wheel pants
• (4) 4mm x 20mm machine screws
• (4) 8mm flat washers
• (4) Lock washers
• (2) Set of axles

TAIL WHEEL ASSEMBLY

• (1) Tail wheel bracket w/wire
• (1) 25mm diameter wheel
• (2) 2mm wheel collar
• (1) 4mm set screw
• (2) Nylon control clasp
• (4) 2mm x 16mm wood screw

ELEVATOR CONTROL SYSTEM

• (2) Clevis
• (2) Silicone tube
• (1) Nylon snap keeper
• (2) Nylon control horn w/plate
• (4) 2mm x 16mm sheet metal screw
• (1) Metal connector
• (1) 1,7mm x 100mm wire pushrod

RUDDER CONTROL SYSTEM

• (1) Clevis
• (1) Silicone tube
• (1) Nylon snap keeper
• (1) Nylon control horn w/plate
• (2) 2mm x 16mm sheet metal screw

AILERON CONTROL SYSTEM

• (2) 1,7mm x 180mm threaded wires
• (2) Clevises
• (2) Silicone tube
• (2) Nylon snap keeper
• (2) Nylon control horn w/plate
• (4) 2mm x 20mm sheet metal screw
• (4) 20mm x 25mm block of woods
• (8) 2mm x 12mm wood screw

KIT CONTENTS: We have organized the parts as they come out of the box for better identification
during assembly. We recommend that you regroup the parts in the same manner. This will ensure you
have all of parts required before you begin assembly.

KIT CONTENTS

MOTOR MOUNT ASSEMBLY

• (4) 3mm x 25mm wood screw

• (4) Lock washer.

THROTTLE CONTROL SYSTEM

• (1) 1,3mm x 500mm wire
• (1) 3,5mm x 350mm nylon pushrod housing
• (1) Metal connector
• (1) 4mm x 4mm machine screw

FUEL TANK

• (1) Nylon fuel tank
• (1) Metal clunk
• (1) Silicone tube / 7cm
• (1) Pre - assembled stopper w / 3 tube
• (1) 165mm x 250mm foam padding

MISCELLANEOUS ITEMS

• (1) Dihedral
• (3) 4mm x 25mm x 140mm light wood
• (6) 25mm light wood triangle stock
• (2) 25mm x 400mm trim tape
• (4) 6mm x 45mm nylon screws
• (4) 3mm x 12mm wood screws
• (1) Decal sheet
• (1) Set of pushrod
• (1) Spinner

ADDITIONAL ITEMS REQUIRED

• 46 Two stroke engine
• 52 Four stroke engine
• 4 Channel Radio with 5 servos
• Glow plug to suit engine
• Propeller to suit engine
• Protective foam rubber
• Silicone fuel line.
• Stick on weight for balance

Made in Vietnam

BALANCING

1. It is critical that your airplane be balanced

correctly. Improper balance will cause your
plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED 105mm
BACK FROM THE LEADING EDGE OF THE
WING, AT THE FUSELAGE. This location is
recommended for initial test flying and trimming.
There is a 5mm margin forward and aft. BALANCE
A PLANE UPSIDE DOWN WITH THE FUEL TANK
EMPTY.

2. Mount the wing to the fuselage. Using a couple

of pieces of masking tape, place them on the
top side of the wing 105mm back from the
leading edge, at the fuselage sides.

3. Turn the airplane upside down. Place your

fingers on the masking tape and carefully lift the
plane .

4. If the nose of the plane falls, the plane is nose

heavy. To correct this first move the battery pack
further back in the fuselage. If this is not
possible or does not correct it, stick small
amounts of lead weight on the fuselage under
the horizontal stabilizer. If the tail of the plane
falls, the plane is tail heavy. To correct this,
move the battery and receiver forward or if this
is not possible, stick weight into the firewall.
When balanced correctly, the airplane should sit
level or slightly nose down when you lift it up
with your fingers.

FLIGHT PREPARATION

PRE FLIGHT CHECK
1. Completely charge your transmitter and receiver

batteries before your first day of flying.

2. Check every bolt and every glue joint in your plane

to ensure that everything is tight and well bonded.

3. Double check the balance of the airplane.

4. Check the control surface.

5. Check the receiver antenna . It should be fully

extended and not coiled up inside the fuselage.

6. Properly balance the propeller.

Elevator Control

Aileron Control

LATERAL BALANCE

After you have balanced a plane on the C.G. You
should laterally balance it. Doing this will help the
airplane track straighter.

5. Turn the airplane upside down. Attach one loop of

heavy string to the engine crankshaft and one to
the tail wheel wire. With the wings level, carefully
lift the airplane by the string. This may require two
people to make it easier.

6. If one side of the wing fall, that side is heavier than

the opposite. Add small amounts of lead weight to
the bottom side of the lighter wing half's wing tip.
Follow this procedure until the wing stays level
when you lift the airplane.

CONTROL THROWS

1. We highly recommend setting up a plane using the

control throws listed.

2. The control throws should be measured at the

widest point of each control surface.

3. Check to be sure the control surfaces move in the

correct directions.

8mm

Rudder Control

28mm

8mm

105mm

Elevator

8mm

12mm

Aileron

8mm

12mm

Rudder

28mm

40mm

INSTALLING THE SWITCH

1. The switch should be mounted on the fuselage side,

opposite the muffler, close enough to the receiver so
the lead will reach. Use the face plate of the switch cut
out and locate the mounting holes.

2. Cut out the switch hole using a modeling knife. Use a

2mm drill bit and drill out the two mounting holes
through the fuselage side.

3. Secure the switch in place using the two machine

screws provided with the radio system.

INSTALLING THE RECEIVER AND BATTERY

1. Plug the servo leads and the switch lead into

the receiver. You may want to plug an aileron
extension into the receiver to make plugging in
the aileron servo lead easier when you are
installing the wing. Plug the battery pack lead
into the switch.

2. Wrap the receiver and battery pack in the

protective foam to protect them from vibration.
Use a rubber band or masking tape to hold the
foam in place.

3. Position the battery pack and receiver behind

the fuel tank. Use the two light plywood pieces,
placed over the battery and receiver and glue to
the fuselage sides to hold the battery and
receiver securely in place. Use 15mm triangle
pieces glued between the fuselage sides and
the plywood pieces to reinforce the joints.

Do not permanently secure the receiver and

battery until after balancing the model.

4. Using a 2mm drill bit, drill a hole through the

side of the fuselage, near the receiver, for the
antenna to exit.

Switch

Receiver

Battery

FINAL ASSEMBLY

PARTS REQUIRED
· (1) Spinner
· (2) 3 mm x 20mm wood screw.

INSTALLING THE SPINNER

Install the spinner back-plate, propeller and
spinner cone. The spinner cone is held in place
using two 3mm x 20mm wood screws.

The propeller should not touch any part of the
spinner cone. If it dose, use a sharp modeling
knife and carefully trim away the spinner cone
where the propeller comes in contact with it.

Cowl area cutout
for proper airflow
to carburetor.