Kurzanleitung RF-TOUCH (4 motorig) / Quick guide RF-TOUCH (4 motors)
27.02.2017
Id-Nr. 85742(a)
4 / 6
Description of button
Drive(s) up:
The drive(s) move and the button is lit blue as long as this button is pressed.
Drive(s) down:
The drive(s) move and the button is lit blue as long as this button is pressed.
Turn the flashlight on/off:
The flashlight is on and the button is lit blue as long as this button is pressed.
Battery indicator:
This button will light red whenever the RF-TOUCH is enabled and the battery voltage
drops below 3.5 V. The batteries must then be replaced.
Floor lighting on/off:
Switch the floor lighting on/off. The button is lit blue when the floor lighting is on.
The floor lighting turns off automatically after 30 minutes.
Synchronous mode on/off:
Two OKIMAT 8 units must be connected to each other using a sync. cable.
Synchronous mode on:
Press this button for about 3 seconds until the backlit illumination blinks twice.
The button is then lit blue.
Synchronous mode off:
Press this button for about 3 seconds until the backlit illumination blinks twice.
The button illumination switches off.
Switchable socket on/off:
Press this button to switch the socket on or off.
The socket is activated when the button is lit blue.
The socket is deactivated when the button is not illuminated.
Child lock mechanism on/off:
Activating the child lock:
Press this button for about 5 seconds until the backlit illumination blinks twice.
The child lock is activated when the button is lit blue.
Deactivating the child lock:
Press this button for about 5 seconds until the backlit illumination blinks
twice. The child lock is deactivated when the button is not illuminated.
The “deactivated child lock” feature does not influence the functionality of the flashlight, switchable
socket, floor lighting, massage modes 1-2-(3) or deactivated massage mode.
Memory position 1:
The drives move to the saved position. The drives move and the button is lit blue as
long as this button is pressed
.
Memory position 2:
The drives move to the saved position. The drives move and the button is lit blue as
long as this button is pressed.
Memory position 3:
The drives move to the saved position. The drives move and the button is lit blue as
long as this button is pressed.
Memory save key:
The drives move to their desired positions. Press the memory save button once: the
“Memory position 1-2-3” button light up. Then press the desired position button within two seconds. The
position is saved in memory.
Massage modes
The massage modes always start at level 1.
Level 1 is the lowest level.
Level 4 is the highest level.
Level 0 means the massage is deactivated. The button is not illuminated.
The activated button will be lit blue. The button lights up blue for the levels 1-2-3-4-3-2-1.
Each time the “Massage mode” button is pressed, the intensity increases or decreases according to
the next level.
When level 4 has been reached, a press of the button will cause the backlit illumination to blink
“white” once.
The levels are in the following sequence: 0-1-2-3-4-3-2-1-0
The sequence repeats after level 0.
When switching massage modes or after the “
Massage mode off
” button has been pressed, the
activated massage mode ends and the corresponding blue illumination switches off.
The massage mode will end after about 15 minutes. The blue button illumination goes out when you
press any button.
o
If the intensity is changed in this time, the massage duration (about 15 minutes) does not
change.
o
If the massage mode is changed in this time, the massage duration (about 15 minutes) starts
over.
An activated massage mode is not interrupted when the drives are moved.
The massage mode can also function while the child lock is enabled.
Massage mode 1:
Stationary intensity: the massage motors run at continual speed.
Massage mode 2:
Pulsing massage: the massage motors change their speed at the same time.
Massage mode 3:
Wave massage: the massage motors change their speed at offset times.
Massage mode off:
This button is lit blue as long as the button is pressed. The “Massage mode
off” button also functions while the child lock is enabled.
Pairing RF-TOUCH
Connect all components to the drive system
Insert the plug into the socket.
Press the
pairing button (a) 2x
until the LED turns on. You now have 10s for the pairing process.
Press and hold the
Paring button (P)
(located in the battery compartment of the RF-TOUCH). The
pairing LED blinks. This LED stops blinking as soon as the pairing is finished.
Only commission
one
system at a time. Never configure multiple systems simultaneously.
Initialization of the RF-Touch
Do not touch the touch surface (surface with the icons) of the RF-TOUCH while the unit is being
commissioned or while the batteries are being changed.
