background image

Amplifier Owner’s Manual

© 2018 Phoenix Gold • www.phoenixgold.com  

SPECIFICATIONS

IMPORTANT: A power birth certificate is included for each amplifier. RX2 amplifiers are 

conservatively rated and will exceed their RMS power rating shown here. All RMS power 

ratings and measurements are at 14.4 volts with no more than 1% THD.

SPECIFICATIONS

Remote Bass Controller:

Under dash or console mountable level controller. Fine tune your bass 

output with a simple turn of the precision controller. Amplifier Status LED for 

easy reference of amplifier. 16ft of cable included.

 

RX2 750.5 SPECIFICATIONS

RMS Power Ratings listed at less than 1% THD @ 14.4v 

Number of Channels:  

5

4Ω: CH 1-4 

60W x 4 

2Ω: CH 1-4 

90w x 4  

4Ω: CH 5 

250W x 1 

2Ω: CH 5 

400w x 1

Total RMS Power (Sum of rated power):  760W

Bridgeable:  

Yes

Crossover Control, Linkwitz-Riley: 

FLAT/HP/LP

 

50Hz - 200Hz @ 12dB/Oct 

Input Selection:  

207mV-5.2v 

Signal to Noise (@ CEA Standard): 

80.1dB

Frequency Response: 

Full Range 10-40k 

 

 

Sub 15-200Hz

Topology Class 

D

Heatsink Type: 

Extruded Aluminum

Cooling Type:  

Radiation 

Operating Voltage:  

8V to 16V

Switchable Auto-Turn On: 

Yes

Power Supply Type: 

Unregulated 

 

Onboard Thermal Management

Power Terminal: 

4 Gauge 

Speaker Terminal: 

12 Gauge

Recommended Fusing: 

3 x 35A 

Dimensions (L x W x H): 

11.81” x 8.11” x 1.98”

 

 

300mm x 206mm x 50.5mm

11.81in /300.00 mm

8.

11

in /

20

6.

00 m

m

1.

98

in

/5

0.

5 m

m

8.11in /206.00 mm

11.81in /300.00 mm

8.

11

in /

20

6.

00 m

m

1.

98

in

/5

0.

5 m

m

8.11in /206.00 mm

11.81in /300.00 mm

8.

11

in /

20

6.

00 m

m

1.

98

in

/5

0.

5 m

m

8.11in /206.00 mm

Summary of Contents for RX2 400.4










Reviews: