manualshive.com logo in svg

Phoenix Contact Axioline F, User Manual, Page: 71 / 86

Share
Download
Phoenix Contact Axioline F User Manual Download Page 71

105739_en_04

PHOENIX CONTACT

71

A  Appendix: glossary for PROFIsafe

A definition of PROFIsafe terms is also provided in the PROFIsafe profile. 

Consecutive number

Method for ensuring that the safe data is transmitted completely and in the correct order.

CRC

Cyclic Redundancy Check

A cyclic redundancy check is used to verify the validity of the process data contained in the 

safety telegram, check whether the assigned address relationships are correct, and verify 

the safety-related parameters. This value is part of the safety telegram.

F-CPU

Failsafe controller, safe controller

F_Destination_Address

F-Parameter; PROFIsafe destination address; address of the safe device: 

see also “F-Parameter”

F-I/O device

Failsafe I/O device; safe input and/or output modules

Modules with integrated safety functions, which are approved for safety-related operation.

F-Parameter

(According to PROFIsafe system description, Version 09, November 2007)

F-Parameters contain information for adapting the PROFIsafe layer to customer 

specifications and for checking the parameterization by means of a separate method 

(diverse). The main F-Parameters are:

F-Slave

Failsafe slave

F-Source_Address

F-Parameter, PROFIsafe source address; address of the safe controller: 

see also “F-Parameter”

F_S/D_Address

(F-Address for 

short)

A unique address for F-Devices within a PROFIsafe island. The 

technology part of the F-Device compares the value with the 

address switch locally or with an assigned F-Address in order to 

check the authenticity of the connection.

F_WD_Time

Specifies the millisecond value for the watchdog timer. The timer 

monitors the time that elapses until the next valid PROFIsafe 

message is received. 

F_SIL

Indicates the SIL that the user can expect from the relevant F-

Device. It is compared with the manufacturer's specification that is 

stored locally.

F_iPar_CRC

A checksum that is calculated from all i-Parameters of the 

technology-specific part of the F-Device.

F_Par_CRC

A CRC signature which is created via all F-Parameters and ensures 

error-free transmission of the F-Parameters.

Summary of Contents for Axioline F























































































Reviews:

No comments