background image

3

Please take the time to read this installation guide before you install the Affinium LED cooler system and LED power driver. 
The guide contains important information and notes regarding the installation and operation.

Warnings

• The installation guide does not supersede local and (inter)national regulations for electrical installations.
• The Philips Affinium LED cooler system and LED power driver must be installed by a professional electrician in accordance with the applicable 

and appropriate electrical codes and the instructions provided by Philips.

• Please note that the driver should be built in (Tcase max. 70 °C).
• The Philips Affinium LED cooler module is designed to be connected to a circuit from a class II power source (Philips LED power driver) with 

energy limited supply. Connection to mains voltage will damage the module. Although the module is fully insulated and unsafe situations are 
unlikely to occur, the module will be damaged beyond repair if it is connected to mains voltage.

• To allow for variance in the installation, it is not recommended to load the power driver beyond 80% of its rated maximum power. The energy 

consumption of the module is a nominal value, with an estimation of 20% deviation.

• Before installation, maintenance or cleaning, always first switch off or disconnect the power and follow appropriate safety procedures.
• Before removing any lens covers or fluorescent lamps, always first switch off or disconnect the mains power to the lighting system.
• Do not use tape to fix the module in position; please use the appropriate mounting sets.
• Do not attempt to replace the power cable to the Philips Affinium LED cooler module because this cable is permanently attached to the 

module.

• Do not make sharp bends with electrical wires.
• Please note that the colors of the wires of different types of cooler(s) may differ. The position of the (original) ballast may also differ.
• Due to the variety of cooler designs and brands, you may need to use customized brackets to fit the specific cooler type you are using. If you 

require further support, please contact your local Philips sales organization.

• To prevent unwanted tripping caused by the inrush current of the LED power driver, an MCB (mini circuit breaker) / fuse (slow blow) of 

at least 6A must be installed. If upgrading the MCB/ fuse, consult a qualified engineer first to ensure that this will not cause any additional 
problems.

 

Cleaning

Use a damp cloth and a mild cleaning agent. Do not wipe the module with a dirty or very wet dishcloth or towel because these may leave
residues that can damage the tube. 
Do not use abrasive cleaners, scouring pads, bleach or cleaners containing bleach because these products can scratch and damage the module.

Important

www.lighting.philips.com/support

Summary of Contents for Value-plus LCM310













Reviews: