10
11
5. Update software
To check for new updates, compare the current software version of your home theatre with the latest
software version (if available) on the Philips web site.
1. Plug in DVD & switch on & connect with TV.
2. Load the software in USB or CD.
3. Insert the USB in DVD & see the display on TV.
4. Press play switch & see processing in TV screen & Do not power off .
5. When the Upgrading complete – the power will be automatic off.
Note – Do not upgrade the software without UPS supply.
7. Troubleshooting
In case these measures do not work contact the nearest PHILIPS service center or call at customer care numbers.
Problem
Solution
1. No power.
2. No sound or distorted sound.
3. The remote control does not
function properly.
4. Low hum or buzz sound.
5. There is no sound from center and rear
6. The content of the USB / SD flash
drive can not be read.
7. FM not properly tuned.
Check if the AC power cord is properly inserted into the AC mains socket.
Adjust the volume / select the correct source to choose the equipment
that you want to hear through the system.
Reduce the distance between the remote control and the system. Replace
the batteries with new ones / Point the remote control directly towards the
IR sensor (located on front panel of the subwoofer) / Check that the batteries
are loaded correctly / Switch off the system for 30 seconds and then restart.
Place the product as far away as possible from electrical devices that may be
causing interference / Check power supply voltage and consult electrician.
Make sure center and rear speakers are connected properly. Make sure
speaker syetem is in 5.1 mode.
The USB / SD flash drive format is not compatible with the system. Drive is
formatted with a different file system which is not supported by this unit (e.g. NTFS)
Match with local frequency.
Warning -
Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty.
Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed
below before taking the system for repair. If you are unable to remedy the problem by following hints
mentioned in below table, Consult your dealer or PHILIPS APSC for help.
6. Product Specifications
Multimedia Amplifier
(Built into the Sub-woofer enclosure)
•Power output (Sub-woofer) - 27W RMS
(Satellite)
- 6.6W x 5 RMS
Separation
- >35db
Audio Input Socket
- RCA type
Audio Output Socket
- RCA type
Satellite speakers
System
- 5 Way, 5 Speakers
Impedance
- 4 Ohms
Speaker size
- 3”
Frequency Range
- 150Hz to 20KHz
Dimensions (WxHxD)
- 105 x 170 x 67 mm
Weight
- 0.58 kg.
Sub-woofer speakers
(With Built-in Multimedia Amplifier)
System
- Vented Enclosure
Impedance
- 4 Ohms
Speaker size
- 5.25”
Frequency Range
- 40Hz to 150Hz
Dimensions (WxHxD)
- 170 x 330 x 335 mm
Weight
- 5.4 kg.
Main unit (DVD player)
Dimensions
- 310 x 37 x 210 mm
Net weight
- 1.1 kg.
Connectivity
Main unit front connection
- Hi-speed USB
Main unit rear connection
- Composite video
(CVBS) output,
AUX-IN
Sub-woofer rear connection - DVD-IN
Video
Signal system
- PAL / NTSC
Composite video output
- 1 Vpp - 75 Ohm
Audio
Analog stereo output
Signal to noise ratio (1 kHz)
- >90 db (A- weighted)
Dynamic range (1 kHz)
- >80 db (A- weighted)
Crosstalk (1 kHz)
- >80 db
Distoration / Noise (1 kHz)
- >70 db
MPEG MP3
- MPEG audio L3
Laser specification
Type
- Semiconductor laser
InGaAip(DVD), AIGaAs(CD)
Wave length
- 655nm (DVD), 790nm (CD)
Output power
- 7.0mW (DVD), 10.0mW (CD)
Beam divergence
- 60 degree
FM
Tuning range
- FM87.5
~
108MHz
Power
Power consumption
- 90W
Standby power consumption - <15
Accessories
-
Remote Control, User
Manual, 2RCA to 2RCA
cable (x3), 3RCA cable
Specifications are subject to change without notice.
Summary of Contents for super star htd2520
Page 1: ...1 ...
