background image

Congratulations

on the purchase of one of the most sophisti-

cated and simple-to-use video recorders (VCR) on the market.
With this VCR you can record and play VHS-standard
cassettes.

Please take the time to read this operating manual before
using your video recorder.

Safety instructions and other notes

Danger: High voltage!
Do not remove the top cover as there is a risk of an electrical
shock!

The video recorder does not contain any components that can be
repaired by the customer. When the appliance is connected to
the power supply there are some components that are constantly
operational. To switch off the video recorder completely you
must disconnect it from the power supply.

Note that this power pack is designed for a power supply of
220-240V/50Hz.

Ensure that air can circulate freely through the ventilation slots
on the video recorder.

Ensure that no objects or liquids enter the video recorder. If liquid
is spilt into it, disconnect the video recorder immediately from the
power supply and call the After-sales Service for advice.

The video recorder should not be used immediately after
transportation from a cold to a hot area or vice versa, or in
conditions of extreme humidity.
After unpacking the video recorder, it should be allowed to
acclimatize for at least three hours before installation.

These operating instructions have been printed on nonpolluting
paper.

Deposit old batteries at the relevant collection points.

Please make use of the facilities available in your country for
disposing of the packaging of the video recorder in a way that
helps to protect the environment.

This electronic equipment contains many materials that can be
recycled. Please inquire about the possibilities for recycling your
old set.

VI and PlusCode are trademarks of Gemstar Develop-
ment Corporation. The VI system is manufactured
under licence from Gemstar Development Corporation.

Contents

Page 1 INSTALLATION 2 2 00 1 Connecting

VCR with scart cable 2 2 00 1 Connecting

VCR without scart cable 2 3 00 1 Adjusting

the modulator frequency 2 3 00 1 Automatic

adjustment of modulator frequency 2 3 00 1

Switching off the modulator 2 3 00 1

Important notes for operation 2 3 00 1 Saving

energy 2 4 00 1 Connecting additional

equipment 2 4 00 1 Emergency interrupt 2 4

00 1 User guide 2 4 00 1 Autoinstall 2 5 00 1

Setting the clock 2 5 00 1 Manual Channel

Number Allocation 2 6 00 1 Monitor function

2 6 00 2 PLAYBACK FUNCTIONS 2 7 00 2

Picture scanning 2 7 00 2 Instant View 2 7 00

2 Still picture 2 7 00 2 Tape position/Index

search 2 7 00 2 Continuous playback 2 8 00 2

Eliminating picture interference 2 8 00 2

Tracking 2 8 00 3 RECORDING FUNCTIONS 2

9 00 3 Long play function 2 9 00 3 Some

general notes for recording 2 9 00 3

Recording from external sources 2 9 00 3

OTR - Recording 2 9 00 3 Erase protection 2

9 00 3 Auto-assembling 2 9 00 3 PDC / VPS 2

10 00 3 Programming with ’VI’ 2 10

00 3 Programming a recording manually 2 11

00 3 Clear a TIMER block 2 11 00 3 Important

programming notes 2 11 00 4 SPECIAL

FEATURES 2 12 00 4 Tuner mode 2 12 00 4

Externally controlled recording 2 12 00 4 On

Screen Display (OSD) 2 12 00 4 Channel

number or frequency display 2 12 00 4

Manual channel search 2 12 00 4 Allocating

a decoder 2 12 00 4 Before you call an

engineer 2 13 00

OPERATING INSTRUCTIONS PHILIPS VR 285

1

Summary of Contents for ShowView VR285

















Reviews: