background image

9

   Tip:

 If the mask frame falls forward on the head and is too close to 

your eyes you may need a larger mask frame.

Using the Mask

1.  Connect the CPAP tubing (included with the CPAP device) to the 

tubing quick release on the elbow.

2.  Turn the therapy device on. Lie down. Breathe normally.
3.  Assume different sleeping positions. Move around until comfortable. 

If there are any excessive air leaks, make final adjustments. Some air 

leaking is normal.

Tubing Quick Release

The elbow is equipped with a tubing 

quick release. Pull on the tubing quick 

release and it will disengage from 

the elbow and come loose with the 

tubing. 

i

Removing the Mask

To keep your adjustments, remove the 

mask by grasping the cushion and pulling 

forward away from the nose. Then pull 

the cushion and mask up and off of the 

head. 

j

5 Mask Care

Cleaning Instructions

Daily: 

Hand wash the non-fabric parts.

Weekly:

 Hand wash the fabric parts.

1.  Disassemble the mask (see 

Disassembly

 section).

2.  Submerge and hand wash the mask in warm water with liquid 

dishwashing detergent.

   Note:

 Ensure there are no air pockets present inside the mask parts 

while submerged.

3.  Rinse thoroughly.
4.  Lay the headgear and fabric sleeves flat or line dry. Make sure the 

entire mask is dry before use.

 Note:

 Do not place the fabric parts into a clothes dryer.

   Caution:

 Any deviation from these instructions may impact the 

performance of the product.

9

10

Summary of Contents for Respironics DreamWear



















Reviews: