background image

LRM2070, LRM2080, LRM2090 Datasheet
OccuSwitch DALI sensor/controller

4/15

Push-button Unit 

The LCU2070 Push-button unit (PBU) makes it possible to connect 
up to 4 switches to the OccuSwitch DALI, to dim and switch different 
DALI groups. This PBU is connected to the DALI channel DA and/
or X for LRM2070 or DA only for LRM2080 and LRM2090. It derives 
its power form the DALI channel, so no additional power supply is 
required. The PBU uses the same interface technique as the one for 
Touch & Dim. Press briefly and it will switch on when off, and off when 
on. When pressed for a longer time, it will alternatively dim up and 
down.

Up to two PBUs can be used on a single OccuSwitch DALI. It is possible 
to interconnect (single) switches to several PBUs to control several 
OccuSwitch DALI units. 
Each LCU2070 connected counts as a driver on the DALI line.

Note: 

the LCU2070 requires the /10 (or higher) versions of the 

OccuSwitch DALI

 LCU2070 

LRM8118 

Max. drivers

 Push button interface 

Extension sensor 

per OSD

 0 

15

 0 

14

 0 

13

 1 

12

 2 

11

Smart Timer

On some occasions with very little movement it is possible that the 
standard delay time of the OccuSwitch DALI is too short. If movement 
is detected during switch off (including fade this takes 10 seconds), the 
delay timer is automatically increased by 10 minutes.

Detection area and shielding

The OccuSwitch DALI detection pattern (see drawing) is 4 by 5 
meters for small movements (desk work) and 6 by 8 meters for larger 
movements like walking. 
We strongly suggest using the 4 by 5 meters for the design. It is also 
the right range for the Light Sensor (for daylight depending regulation). 
The detection area of the movement detector can be extended by two 
extension sensors (LRM8118) each with a equal detection pattern as 
the OccuSwitch DALI.

8m

5m

6m

4m

120°

If the shield is retracted the 
detection pattern will be cut on 
one side (120°) as indicted in the 
diagram.

Black

Black

White
Red
Purple
White

Green

Yellow

COM

DA -

DA +

SW1
SW2
COM
SW3
SW4

Common

DALI line on OccuSwitch DALI

(Window) Touch and Dim
( Co Extra Auto-on) Touch and Dim + Daylight Dependent Regulation
Common
(Corridor) Touch and Dim
(Extra Manual-on) Touch and Dim

LCU2070/00

9137 003 35103
Made in E.U.

PFT yyww

DA+

DA -

1

2

3

4

5

6

LCU2070 wiring

Detection pattern

click

click

For all functions

                   1                                         0

press shortly
0 lights off
1 lights on

press longer
0 lights dim down
1 lights dim up

LCU2070 Push-button unit

Summary of Contents for OccuSwitch DALI LRM2070
















Reviews: