-
Charging or using the product at
temperatures below 40 °F (4.5 °C) or higher
than 95 °F (35 °C) adversely affects the
lifespan of the battery.
-
If the product is subjected to a major
change in temperature, pressure or
humidity, let the product acclimatize for 30
minutes before using.
Quick charge: During quick charge, all three
lights of the battery charge indicator light
up. After approx. 5 minutes of charging, the
product contains enough energy for 5 minutes
of use. When quick charge is finished, the
bottom light of the battery charge indicator
starts to flash.
Charging with the power cord
1 Make sure the product is switched off.
2 Insert the small plug into the product and
put the power plug in any 120V AC outlet
(Fig. 4).
3 After charging, remove the power plug
from the wall outlet and pull the small plug
out of the product.
Note: Approx. 30 minutes after the battery
is fully charged or when you disconnect the
product from the outlet, the battery charge
indicator switches off automatically.
Running time
When the product is fully charged, it has a
cordless running time up to 90 minutes.
Using the product
Note: This product is for cordless use only
(Fig. 5).
-
Use this product for its intended household
use as described in this manual.
-
For hygienic reasons, the product should
only be used by one person.
-
Trimming is easier when the skin and hair
are dry.
-
Use the product to trim, edge or shave
facial hair (beard, mustache and sideburns).
-
Trim with the trimming comb to obtain a
certain length.
-
Take your time when you first start to use
the product. You have to gain practice with
the product.
-
Allow some time for the skin to adjust to
the product.
-
Use the blade on a clean face. The blades
go blunt faster if on skin that isn‘t clean.
-
Do not use the blade when damaged or
broken. Replace the blade immediately if it
is damaged.
This product is not intended for shaving,
edging or trimming hairs on lower body
parts or scalp hair.
Switching the product on and off
1 Press the on/off button once to switch the
product on or off (Fig. 6).
Shaving
-
Shave off any length of hair. The product
does not shave as close as a traditional
blade so your skin will stay comfortable.
-
Make sure that the blade is in full contact
with the skin by placing it flat on the skin.
-
For the best result, move the product
against the grain.
-
Make long strokes while pressing lightly.
-
Use the product dry or wet with gel or
foam, even in the shower.
-
Shaving a clean beard and face gives the
best results.
2 Switch on the product (Fig. 6).
3 Place the blade on the skin and move the
product upwards or against the grain in
long strokes while pressing lightly (Fig. 7).
Note: Make sure you hold the surface of the
blade flat against your skin (Fig. 8).
4 Switch off and clean the product after each
use (see ‘Cleaning’).
Edging
-
Use both edges of the blade to create sharp
lines and perfect edges.
-
Hold the product in such a way that the
blade is perpendicular to the skin and one
of its edges touches the skin. This allows
more precise detailing of sideburns and the
area around the mouth and nose.
1 To create sharp edges and lines, you can
use either edge of the blade (Fig. 9).
2 Switch on the product (Fig. 6).
3 Place the edge of the blade perpendicular
onto the skin (Fig. 10).
4 Make straight strokes while applying gentle
pressure (Fig. 11).
5 Switch off and clean the product after each
use (see ‘Cleaning’).
Using the precision trimming comb
-
The precision trimming comb allows you
to trim hair to different lengths. When you
trim for the first time, start at the highest
length setting to familiarize yourself with
the product.
-
The settings on the wheel correspond to
the remaining hair length after trimming
in millimeters. You can select a length
from 0.5 mm (1/64 in.) to 9 mm (23/64 in.)
(Fig. 12).
-
Always trim in the direction of the teeth
of the precision trimming comb, making
sure that the flat part of the comb is in full
contact with the skin for an even trimming
result (Fig. 13).
-
Since all hairs do not grow in the same
direction, you may want to try different
trimming directions (i.e. upwards,
downwards, or across). Practice is best for
optimum results.
-
Make sure to always move the product
against the grain.
-
Trimming is easier when the skin and hair
are dry.
1 Place the front part of the comb onto the
blade and push the projection at the back
of the comb into the product (‘click’) (Fig.
14).
2 Turn the hair length setting wheel to select
the desired hair length setting (Fig. 15). The
settings on the wheel correspond to the
remaining hair length after trimming.
3 Switch on the product (Fig. 6).
4 Place the comb onto the skin and move the
product upwards slowly, against the grain
(Fig. 16).
5 Switch off and clean the product after each
use (see ‘Cleaning’).
6 To remove the comb, pull the back part off
the product and then slide the comb off the
blade (Fig. 18).
Cleaning
Clean the product after every use.
Never use scouring pads, abrasive cleaning
agents or aggressive liquids such as
gasoline or acetone to clean the product.
Do not tap the product or blade against a
surface to remove hairs and water as this
may cause damage to the product and
blade (Fig. 17). If the blade is damaged,
replace immediately.
Never dry the blade with a towel or tissue,
as this may cause damage.
Cleaning the product
1 Switch off the product.
2 Remove the comb from the blade (Fig. 18).
3 Blow off any hairs that have accumulated
on the blade and/or comb.
4 Switch on the product for approx. 15
seconds and rinse the blade with lukewarm
water.
5 Rinse the comb for approx. 15 seconds with
lukewarm water (Fig. 19).
6 Carefully shake off excess water and let all
parts air dry completely.
Note: The blade is fragile. Handle it carefully.
Replace the blade immediately if it is
damaged.
This product has no other user-serviceable
parts. For assistance call 1-800-243-3050.
Storage
Always put the protection cap on the blade to
protect the blade from damage during travel
or storage.
We advise you to let the product and its
attachments dry completely before you store
them for the next use.
1 Place the protection cap onto the edge of
the blade (Fig. 20).
2 Close the protection cap (Fig. 21).
-
Charge the battery before storing the
product for an extended period.
-
Be sure the product is switched off. Remove
the power cord from power outlet and
the product before storing it in a safe,
dry location where it will not be crushed,
banged, or subject to damage.
-
Do not wrap cord around the product
when storing.
-
Store cord and other accessories in a safe
location where these will not be cut or
damaged.
-
Do not place or store the product where
it can fall or be pulled into a tub or sink,
water or other liquid while plugged in.
Replacement
Blade wear indicator
For optimal cutting and gliding performance,
replace the blade every 4 months or when it
no longer provides the shaving or trimming
results you expect. This advice is based on two
full shaves a week and actual results may vary.
Depending on your usage behavior, the
exact lifetime of the blade could be longer or
shorter. Similar to a manual blade, the blade
becomes blunt over time, which results in
increased hair pulling and reduced cutting
performance.
A replacement symbol will gradually appear
on the blade as you use it (Fig. 22). When the
replacement symbol is fully visible, it‘s time to
replace your blade.
Note that accessories such as guards can
prevent the replacement symbol from
becoming visible.
Tip: the replacement symbol resembles the
icon on the blade release button of your
OneBlade. For older blades, a green rectangle
may appear in place of the replacement
symbol.
Replacing the blade
1 Make sure that the product is switched off.
2 Carefully push the blade release slide
switch upwards while holding the blade on
both sides (Fig. 23). This prevents the blade
from being ejected from the handle.
3 Hold the new blade on both sides and press
it onto the handle (‘click’) (Fig. 24).
Note: Be careful, the edges of the blade are
sharp. When you hear a click, the new blade is
placed correctly and ready for use.
Accessories
Replacement parts and accessories may
be purchased at a store near you or on our
website
www.philips.com/store
.
The following accessories are available:
-
Model QP210 Philips Norelco Replacement
Blade, 1-Pack
-
Model QP220 Philips Norelco Replacement
Blade, 2-Pack
-
Model QP230 Philips Norelco Replacement
Blade, 3-Pack
-
Model QP610 Philips Norelco Body Kit
-
Model QP620 Philips Norelco Face +
Body Kit
Assistance
For assistance, visit our website:
www.philips.com/support
or call toll free
1-800-243-3050.
Online information is available 24 hours a day,
7 days a week.
Disposal
-
This product contains a rechargeable
lithium-ion battery which must be disposed
of properly.
-
Contact your local town or city officials
for battery disposal information. You
can also call 1-800-822-8837 or visit
www.call2recycle.org
for battery drop-off
locations (Fig. 25).
-
For assistance, visit our website
www.philips.com/support
or call
1-800-243-3050 toll free.
-
Your product is designed and
manufactured with high quality
materials and components, which can
be recycled and reused. For recycling
information, please contact your local
waste management facilities or visit
www.recycle.philips.com
.
Full Two-Year Warranty
Philips North America LLC warrants this new
product (except blade and comb) against
defects in materials or workmanship for a
period of two years from the date of purchase,
and agrees to repair or replace any defective
product without charge.
IMPORTANT
: This warranty does not cover
damage resulting from accident, misuse or
abuse, lack of reasonable care, the affixing of
any attachment not provided with the product
or loss of parts or subjecting the product to
any but the specified voltage or batteries.*
NO RESPONSIBILITY IS ASSUMED FOR ANY
SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
In order to obtain warranty service, simply go
to
www.philips.com/support
for assistance.
It is suggested that for your protection you
return shipments of product by insured mail,
insurance prepaid. Damage occurring during
shipment is not covered by this warranty.
NOTE: No other warranty, written or oral, is
authorized by Philips North America LLC.
This warranty gives you specific legal rights,
and you may also have other rights which
vary from state to state. Some states do not
allow the exclusion or limitation of incidental
or consequential damages, so the above
exclusion and limitations may not apply to
you.
*Read enclosed instructions carefully.
45-DAY MONEY-BACK GUARANTEE
If you are not fully satisfied with your product
send the product back and we’ll refund you
the full purchase price.
The product must be shipped prepaid by
insured mail, insurance prepaid, have the
original sales receipt, indicating purchase
price and date of purchase, and the money-
back guarantee return authorization form
enclosed.
We cannot be responsible for lost mail.
The product must be postmarked no later
than 45 days after the date of purchase. Philips
reserves the right to verify the purchase price
of the product and limit refunds not to exceed
suggested retail price.
To obtain the money-back
guarantee service, please go to
www.PhilipsMoneyBack.com and follow
the simple 3-step process.
Delivery of refund check will occur
6–8 weeks after receipt of returned
product.
QP6531-CALIBURN-US_3000.094.0446.1_LFLT_foldedA7_BW.indd 5-8
QP6531-CALIBURN-US_3000.094.0446.1_LFLT_foldedA7_BW.indd 5-8
21-07-22 15:22
21-07-22 15:22
