32 Beard brush
Not shown: cleaning brush
This symbol indicates that the product can be used in the bath or
shower.
Charging
Battery status indications
- When the battery is almost empty, the battery status indicator
lights up orange (Fig. 2).
- When the product is charging, the battery status indicator
flashes white slowly.
- During quick charge, the battery status indicator flashes white
quickly. After approx. 5 minutes of charging, the battery
indicator flashes white slowly. The product now contains
enough power for one cordless trimming session.
- When the battery is fully charged, the battery status indicator
lights up white continuously.
Note: After approx. 30 minutes, the light goes out automatically.
Charging
Charge the product before first use and when the display
indicates that the battery is almost empty. When the product has
charged for 3 hours, it has a cordless operating time of up to 6
hours.
- Charging, recharging or using the product at temperatures
below 40°F (4,5°C) or higher than 95°F (35°C) adversely affects
the lifespan of the battery.
- If the product is subjected to a major change in temperature,
pressure or humidity, let the product acclimatize for 30
minutes before use.
1 Make sure the product is turned off.
2 Insert the small plug into the product and put the power plug
in any 120V AC outlet (Fig. 3).
3 After charging, remove the power plug from the wall outlet and
pull the small plug out of the product.
Note: An adapter plug may be necessary for cord usage in some
foreign countries. Use an attachment plug adapter of the proper
configuration for power outlet.
Quick charge
After approx. 5 minutes charging, the product contains enough
power for one cordless trimming session.
Using the product
Always check the product and all accessories before use. Do not
use the product or any accessory if it is damaged, as this may
cause injury. Always replace a damaged part with one of the
original type.
Note: This product can only be used without a cord.
Note: Turn off and clean the product and attachments after each
use
- Use this product for its intended household use as described
in this manual.
- For hygienic reasons, the product should only be used by one
person.
Trimming is easier when the skin and hair are dry.
Detaching and attaching cutting elements
1 To detach a cutting element, push upwards against the teeth
of the cutting element and take it off the handle (Fig. 4).
2 To attach a cutting element, insert the lug of the cutting
element into the guiding slot at the front and push the back of
the cutting element onto the product ('click') (Fig. 5).
Detaching the precision shaver and nose trimmer
1 Place your finger on the arrow at the back of the attachment
and push it off the handle in the direction of the arrow (Fig. 6).
Attaching and detaching guards
1 To attach any type of guard onto a cutting element,
slide the
front part of the guard onto the teeth and push the projection
at the back of the guard into the product ('click') (Fig. 7).
2 To detach any type of guard from the cutting element,
carefully pull its back part off the product and then slide it off
the cutting element (Fig. 8).
Note: When trimming for the first time, start by using the guard
with the maximum trimming length setting to familiarize
yourself with the product.
Turning the product on and off MG7791
1 Press the on/off button once to turn the product on or off (Fig.
9).
Attachments for use on beard
Full-size hair trimmer
Use the full-size hair trimmer without a guard to trim hair close to
the skin (to a length of 1/32in./0.5mm) or to create clean lines
around your beard, neck and sideburns.
1 To trim hair close to the skin, place the flat side of the cutting
element against your skin and make strokes against the
direction of hair growth (Fig. 10).
2 For contouring, hold the cutting element perpendicular to the
skin and move it upwards or downwards with gentle pressure
(Fig. 11).
Beard guards
Attach a beard guard to the full-size hair trimmer to trim your
beard and moustache evenly. The product comes with 6 beard
guards. The hair length settings are indicated on the guards. The
settings correspond to the remaining hair length after trimming.
Guard
inch
mm
Stubble guard
3/64 in.
1 mm
Stubble guard
5/64 in.
2 mm
Beard guard
1/8 in.
3 mm
Beard guard
3/16 in.
5 mm
Beard guard
9/32 in.
7 mm
Adjustable guard
1/8 in.- 9/32 in.
3 mm-7 mm
1 Attach the guard to the full-size hair trimmer.
2 Adjustable guard: Push the length selector to the left or right
to select the desired hair length setting (Fig. 12).
3 To trim in the most effective way, move the guard against the
direction of hair growth (Fig. 13). Make sure the surface of the
guard always stays in contact with the skin.
Attachments for use on body
- Use the green body guards to trim body hair.
- When you trim for the first time, use the 5 mm/3/16 in. body
guard to familiarize yourself with the product.
- Body hair can be trimmed wet or dry, however dry is
preferable because wet hair tends to stick to the body. Also
when trimming sensitive areas, always use a body guard.
- Since all hairs do not grow in the same direction, you may
want to try different trimming positions (i.e. upwards,
downwards, or across). Practice is best for optimum results.
- Always make smooth and gentle movements and be sure the
surface of the guard always stays in contact with your skin.
- When too many hairs have accumulated on the product, blow
the hairs out before use, for best trimming results.
Body guards
Attach a body guard to the full-size hair trimmer to trim hairs
below the neckline. The product comes with 2 body guards. The
hair length settings are indicated on the guards. The settings
correspond to the remaining hair length after trimming.
