Philips Norelco G270 User Manual Download

Page: 3 / 17

60-DAY

MONEY-BACK

GUARANTEE

If you are not fully satisfied with your Norelco Groomer,
send the product back and we’ll refund you the full
purchase price.
The Groomer must be shipped prepaid by insured
mail, insurance prepaid, and have the sales receipt,
indicating purchase price and the date of purchase,
enclosed. The Groomer must be postmarked no later
than 60 days after the date of purchase. Norelco
reserves the right to verify the purchase price of the
Groomer and limit refunds not to exceed suggested
retail price.
Send dated sales receipt, your complete name and
address as indicated below, and the Groomer, prepaid to:

Philips Domestic Appliances

and Personal Care Company

A Division of Philips Electronics

North America Corporation

450 North Medinah Road, Dock 16

Roselle, IL 60172-2329

Please allow 4-6 weeks for delivery of check.

(Please Print)

Name ________________________________________

Address_______________________________________

City__________________________________________

State__________________Zip_____________________

Daytime Telephone No. (_____)____________________

E-mail Address: _________________________________

REASON FOR RETURNING:

______________________________________________

_______________________________________

________________________________________

Defining Beard, Moustache and
Sideburns

Be certain the Groomer is in the OFF position.

Remove the AccuControl comb attachment
by pressing and sliding the Hair Length
Selector upwards (fig. 9).

Detach the full width trimmer attachment by
pushing the release button (fig. 10).

Put the smaller neckline and sideburn
trimmer attachment on the Groomer (fig. 11).
You will hear a click.

◗

Hold the Groomer upright when you use the
smaller neckline and sideburn trimmer
attachment (fig. 12).

Using Nose, Ear & Eyebrow
Attachment

Be certain the Groomer is in the OFF
position.

To attach or remove nose, ear, eyebrow
attachment (or change attachments):

◗

Remove the AccuControl comb attachment
(fig. 9).

◗

Remove the full width trimmer attachment by
pushing the release button (fig. 10).

◗

Put the nose, ear, eyebrow attachment on the
Groomer (fig. 13).You will hear a click.

Trimming Nose Hair

◗

Make sure nasal passages are clean.

Place nose, ear and eyebrow attachment on
Groomer.

Switch the Groomer ON and insert the tip
of the attachment into one nostil (fig. 14).

CAUTION: Do Not insert the tip more
than 3/16 in./5mm into your nostril.

Slowly move the tip in and out while turning
it around at the same time in order to
remove unwanted hair. For best results, make
sure the side of the tip is firm against skin.
This will reduce the tickling effect that can
occur during trimming of nose hair.

Turn off Groomer. Wipe attachment clean
after each use.

Trimming Ear Hair

◗

Clean outer area of ear and ear canal. Make
sure it is free of wax.

◗

Nose, ear and eyebrow attachment should be
on the Groomer.

Switch the Groomer on and move the tip
softly around the edge of ear to remove
hairs extending beyond the outer ear (fig. 15).

Carefully insert the tip into outer ear canal.

CAUTION: Do not insert the tip further
than 3/16 in./5mm into the ear as this
could cause damage to the eardrum
(fig. 16).

Turn off Groomer. Wipe attachment clean
after each use.

Trimming Eyebrow

◗

Nose, ear and eyebrow attachment should be
on Groomer.

Switch the Groomer on and use the tip to
cut individual eyebrow hairs.

The Groomer can be used for clipping single long
hairs.

Put the Groomer at the root of the hair and
move it along the edge of the eyebrow from
the base of the nose towards the outer tip
of the eyebrow in the direction of hair
growth (fig. 17).

IMPORTANT: Do not use the Groomer to define
or trim the entire eyebrow. Do not try to trim
your eyelashes. Be careful not to get too close to
your eyelashes and eyes!

Turn off Groomer. Wipe attachment clean
after each use.

Trimming your Beard & Moustache
with AccuControl Guide Comb
Attachment

◗

Use this Groomer for its intended household
use as described in this manual.

◗

Make sure that the Groomer is fully charged
before you start trimming. This Groomer will
not operate while cord is connected to
electrical outlet.

Put the AccuControl comb on the full width
trimmer attachment until you hear it click
into place (fig. 6).The AccuControl comb will
not work with the smaller neckline and
sideburn trimmer attachment.

Press the Hair Length Selector and slide it to
the desired trimming length setting.The
selected setting number will appear in the
window to the left of the Hair Length
Selector (fig.7). See Table 1 for settings.

◗

If you are trimming for the first time, start by
using the AccuControl comb at the maximum
trimming length setting (#9) to prevent
accidentally trimming hairs too short. As you
become familiar with the settings, adjust Hair
Length Selector to desired trimming length.
Selector will "click" into position at each
setting.

Switch the Groomer ON.

To trim in the most effective way, move the
Groomer against the direction of hair
growth. Make sure the surface of the Guide
Comb always stays in contact with the skin
(fig. 8).

NOTE: Since all hairs do not grow in the same
direction, you may want to try different trimming
directions (i.e., upwards, downwards, or across).
Practice is best for optimum results.

◗

If a lot of hair has accumulated in the Guide-
Comb, remove the comb and blow and/or
shake the hair out of the comb.You can also
use the cleaning brush provided to remove
hair from the comb area.

◗

REMEMBER:You must reset the hair length
selector back to your desired setting every
time you replace the guide comb on the
appliance.

◗

The remaining hair length corresponds with
the smallest distance between the cutting
blade and the spot where the comb is in
contact with the skin.

◗

Cutting without the comb attachment or
setting the AccuControl guide comb to
#1 position will result in a stubble beard look.

Beard Trimming Without
AccuControl Guide Comb

Remove AccuControl guide comb if you are:

◗

Defining hair lines

◗

Trimming nape of neck

◗

Removing single, unwanted hairs

Be certain the Groomer is in the OFF position.

Remove the AccuControl comb attachment
by pressing and sliding the Hair Length
Selector upwards (fig. 9).

Never pull off the AccuControl comb
attachment by grasping the flexible top portion.
Always pull off by the bottom part attachment.

Switch the Groomer ON.

Make well-controlled movements.Touch the
hair/skin lightly with the Groomer.

Hair Clipping

◗

Make sure that the appliance is fully charged
before you start clipping hair. The appliance
will not operate while cord is connected to
electrical outlet.

◗

Before you start clipping, make sure that the
head of the person whose hair you are cutting
is at the same level as your chest so that all
parts of his/her head are clearly visible and
within easy reach.

◗

Only use the appliance on dry hair.

◗

Do not use on freshly washed hair.

◗

Before you begin, comb the hair in the
direction of growth.

◗

To achieve optimal clipping results, always

move the appliance slowly through the hair
against the direction of hair growth.

Clipping with hair comb attachment

Put the hair clipper comb on the full width
trimmer attachment and push until you hear
it ‘click’ into place (fig. 18).

Press the Hair Length Selector and slide it to
the desired setting. See Table 2.

The setting selected will appear in the
window to the left of the Hair Length
Selector (fig. 19).

When you are clipping for the first time, start at
the maximum clipping length setting (#9) to
familiarize yourself with the appliance and prevent
accidentally trimming hairs too short. As you
become familiar with the settings, adjust the Hair
Length Selector to desired trimming length.
Selector will ‘click’ into position at each setting.

Make sure that the flat part of the comb is
always in full contact with the scalp to obtain
an even result (fig. 20-21).

Move the appliance slowly over the crown
from different directions to achieve an even
result (fig. 22).

Always move the appliance against the
direction of hair growth.

Make overlapping passes over the head to
ensure that all hair that should be cut has
been cut.

Turn the Groomer off and remove the hair
comb often to blow and/or shake out hair
that has accumulated.

◗

REMEMBER:You must reset the hair length
selector back to your desired setting every
time you replace the hair clipping comb on the
appliance.

Contouring without the hair clipping
comb attachment

Remove the hair comb by pressing and
sliding the Hair Length Selector upwards
(fig. 23).

Be careful when you are clipping without comb
attachment as when the appliance is turned on it
will trim every hair it touches.

Tilt the appliance in such a way that only
one edge of the trimming attachment
touches the hair ends when you shape the
contours around the ears (fig. 24).

To contour the nape of the neck or hairline,
turn the appliance and hold it with the
trimming attachment pointing downwards
(fig. 25).

To contour the sideburns, turn the appliance
and hold it with the trimming attachment
pointing downwards (fig. 26).

ENGLISH

IMPORTANT

SAFETY

INSTRUCTIONS

When using an electrical appliance, basic safety
precautions should always be followed, including
the following:

Read all instructions before using this
appliance.

DANGER

To reduce the risk of electric shock:

1. Do not reach for a Groomer that has fallen

into water. Unplug immediately.

2. Do not use while bathing or in a shower.
3. Do not place or store Groomer where it

can fall or be pulled into a tub or sink. Do
not place in or drop into water or other
liquid.

4. Always unplug this Groomer from the

electrical outlet immediately after using,
except when Groomer is (re)charging.

5. Unplug Groomer before cleaning.
6. When discarding Groomer, unplug Groomer

to remove rechargeable battery. See Battery
Removal instruction sheet.

WARNING

To reduce the risk of burns, fire, electric
shock or injury to persons:

1. Close supervision is necessary when

this appliance is used by, on, or near children
or invalids.

2. Use this Groomer for its intended

household use as described in this manual.
Do not use attachments not recommended
by Philips Electronics North America
Corporation.

3. Never operate this Groomer if it has a

damaged cord or plug, if it is not working
properly, if it has been dropped, damaged, or
dropped into water. Return the Groomer to
an Authorized Norelco Service Location for
examination and repair.

4. Keep the Groomer, cord and any

attachments away from heated surfaces.

5. Never drop or insert any object into any

opening.

6. Do not operate, charge or plug in Groomer

outdoors or where aerosol (spray) products
are being used or where oxygen is being
administered.

7. Do not use this Groomer with a damaged

or broken cutter, or cutting unit as injury
may occur.

8. Always attach plug to Groomer first, then to

outlet.To disconnect, turn on/off switch to
“OFF” position (switch is down), then
remove plug from outlet.

9. To prevent possible damage to the cord, do

not wrap cord around the Groomer.

10. Never put Groomer in direct sunlight or

store at a temperature above 140°F.

11. This Groomer is for use on human facial

hair only. Do not use this Groomer for any
other purpose.

12. Always store your Groomer, attachments

and power plug in a moisture-free area.
Make sure the cord is disconnected from the
Groomer.

SAVE THESE

INSTRUCTIONS

IMPORTANT:YOUR GROOMER CONTAINS
A NICKEL-CADMIUM RECHARGEABLE
BATTERY.

See Battery Removal instruction sheet.

IMPORTANT:The power plug contains a
transformer. Do not cut off the power
plug to replace it with another plug as this
will cause a hazardous condition.

To Charge/Recharge

◗

Fully charge Groomer before using for the
first time or after non-use for a long period of
time.

◗

Battery performance is best if you recharge
only when the battery is (almost) completely
empty.

◗

Charging or recharging at temperatures below
40˚F or higher than 95˚F adversely affects
lifespan of the battery.

◗

Continuously recharging Groomer will reduce
lifespan of battery.

Be certain Groomer is OFF.

You may charge the Groomer:

◗

In the charging stand by inserting the plug into
the socket located in the bottom of the
charging stand (fig. 2). Place the Groomer
directly on the charging pin in the stand (fig. 3).

◗

By inserting the charging plug directly into the
Groomer (fig. 4).

Plug charging plug into any 120V AC outlet.
Use only the cord provided.

After a few moments, the green Charging
Indicator Light on the power plug will light
to indicate the Groomer is charging (fig. 5).

◗

It will take approximately 10 hours to fully
charge the Groomer for a cordless trimming
time of up to 35 minutes.

◗

Disconnect the cord and unplug from
electrical outlet.

Optimize the working life
of the battery

◗

After the Groomer has been charged for the

first time, do not recharge the Groomer
between trimming sessions. Continue using it
until the battery is completely empty.

◗

Do not charge for more than 24 hours.

◗

Do not keep cord permanently plugged in.

◗

Discharge/run down the battery completely
twice a year by letting the motor run until it
stops.

◗

If the Groomer hasn’t been used for a long
period of time, it must be recharged for a
full 10 hours.

Cordless Trimming

Charge according to directions. Unplug
Personal Groomer from outlet.

Slide ON/OFF switch ON to begin trimming.

If the battery is empty and you want to trim
your beard, charge the Groomer for at least
3 hours and you will have enough power for
one use (10 minutes).

Put It To The Test

Like many new products, your Norelco Personal
Groomer may take a little getting used to. If you
are using an electric Personal Groomer for the
first time, or if you’ve been using a different brand,
take the time to acquaint yourself with your new
Personal Groomer.

Your Personal Groomer features the unique
AccuControl System combined with adjustable
Length Settings to make trimming facial hairs
or hair clipping goof proof.

Throw your scissors away and put your new
Personal Groomer to the test. We guarantee
precise, professional results or Norelco will refund
you the full purchase price.

AccuControl System

The unique Norelco AccuControl System puts
you in complete control while trimming your
facial hairs with no prior experience needed.The
flexing Guide Comb adjusts automatically to hug
the contours of your face for a trim that is both
even and accurate. And, it’s easy to maneuver
over those hard-to-reach areas such as the throat
and chin.The Hair Length Selector allows you to
choose among 9 preset hair lengths and clicks
into position so you can control the exact hair
length you desire or vary the length of your facial
hair. The Hair Clipping Comb also features 9
preset hair lengths and clicks into position so you
can control the exact hair length you desire. The
Norelco Personal Groomer for professional, goof-
proof results every time or your money back.

Trimming

◗

Make sure hair is clean and dry.

◗

Always comb the hair with the styling comb in

the direction of growth before you start
trimming.

Do not move the Groomer too fast. Make
smooth and gentle movements.

Cleaning

◗

Do not use water or a moist cloth to clean
the Groomer.

◗

Always switch Groomer OFF before cleaning.

◗

Do not use abrasive, scourers or liquids such
as alcohol, benzene, bleach or acetone to clean
the Groomer.

◗

Never clean, replace or remove Groomer
attachments with motor ON.

◗

Do not apply pressure to cutters.

◗

Do not touch cutters with hard objects as this
may damage them.

◗

Do not use while bathing, showering or
immerse the Groomer in water or other
liquids as damage to Groomer may occur.

During Use:

◗

If cut hairs have accumulated in the Guide
Comb area, remove hairs by shaking, blowing
or using cleaning brush provided. Remember
to adjust the trimming length back to your
selected setting when you replace the guide
comb on Groomer.

Once a Week:

Make sure the Groomer is switched OFF
and disconnected from the electrical outlet.

Remove any attachments.

Blow and/or shake out any hair that may
have accumulated in the attachment.

Clean the outside and inside of the
attachment with the brush supplied (fig. 27).
The cutter is fixed to the trimming
attachment(s) and cannot be removed.

Place the attachment back on Groomer or
place in the storage stand (fig. 28).

This Groomer has no other user-serviceable
parts. Any other service should be performed by
an Authorized Norelco Service Location.

Storage

◗

Be sure Groomer is turned OFF. Remove cord
from outlet and Groomer before storing in a
safe, dry location where it will not be crushed,
banged, or subject to damage.

◗

Store the Groomer and attachments in the
storage stand to prevent damage.

◗

Do not wrap cord around Groomer or stand
when storing.

◗

Store cord in a safe location where it will not
be cut or damaged.

◗

Do not place or store Groomer where it can
fall or be pulled into a tub or sink, water or
other liquid while plugged in.

Replacing The Cutting Unit

If your cutters become damaged or worn, do not
continue using the Groomer. Cutters should be
replaced immediately by an Authorized Norelco
Service Location.

Assistance

For assistance or the Authorized Norelco Service
Location nearest you, call toll free:

1-800-243-3050
or visit our website: www.norelco.com

Authorized Norelco Service Location information
is available 24 hours a day, 7 days a week.

Battery Removal

◗

This Norelco Groomer contains a

rechargeable Nickel-Cadmium battery, which
must be disposed of properly.

◗

Battery should only be removed when
Groomer is to be discarded.

◗

Refer to Battery Removal instruction sheet for
directions on removing the rechargeable
battery.

A. Neckline & Sideburn Trimmer Attachment
B. Full Width Trimmer Attachment
C. Lifetime Self-Sharpening 3-Dimensional

Rounded Stainless Steel Cutter Blades

D. AccuControl Beard & Moustache Trimmer

Guide Comb

E. Hair Clipping Comb
F.

9 Position Hair Length Selector

G. Release Button
H. On/Off Slide Switch
I.

Socket for appliance plug

Cleaning Brush

K. Styling Comb
L. LED Charging Indicator Light on Adaptor
M. Appliance Plug
N. Charging Plug
O. Nose, Ear, Eyebrow Trimmer Attachment
P.

Charging/Storage Stand
Full Two-Year Warranty
60-Day Money-Back Guarantee

Nor

elco

Features

Remaining hair length
(mm)

Setting

Table 2. Hair clipper

Remaining hair length
(mm)

Setting

Stubble

Closely Cropped

Short

Medium Short

Medium

Medium Long

Long

Extra Long

Longest

Table 1. Beard trimmer

MAX 0.5cm

fig. 1

Full Two-Year Warranty

Philips Electronics North America Corporation warrants each new
Norelco product, Model G270, against defects in materials or
workmanship for a period of two years (cutters for up to five years)
from the date of purchase, and agrees to repair or replace any defective
product without charge.

IMPORTANT:

This warranty does not cover damage resulting from

accident, misuse or abuse, lack of reasonable care, the affixing of any
attachment not provided with the product or loss of parts or subjecting
the product to any but the specific voltage.* Use of unauthorized
replacement parts will void this warranty.

PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY A
NON-AUTHORIZED REPAIR SERVICE AND WILL NOT
REIMBURSE THE CONSUMER FOR DAMAGE RESULTING
FROM WARRANTY SERVICE PERFORMED BY A NON-
AUTHORIZED REPAIR SERVICE.
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.

In order to obtain warranty service, simply take or ship the product
postage prepaid to the nearest Authorized Norelco Service Location. It is
suggested that for your protection you return shipments of product by
insured mail, insurance prepaid. Damage occurring during shipment is not
covered by this warranty.

NOTE:

No other warranty, written or oral, is

authorized by Philips Electronics North America Corporation.This
warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the
above exclusion and limitations may not apply to you.
*Read enclosed instructions carefully.

Manufactured for:
Philips Domestic Appliances and Personal Care Company
A Division of Philips Electronics North America Corporation
1010 Washington Blvd., Stamford, CT 06912-0015

This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories, Inc.

Norelco is a Registered Trademark of Philips Electronics
North America Corporation.
AccuControl is a Trademark of Philips Electronics North America Corporation.

PHILIPS is a Registered Trademark of Koninklijke Philips Electronics N.V.

Area Code

NewG270_2005 1/17/06 2:58 PM Page 1 (Black plate)