background image

3

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC

SHOCK. DO NOT OPEN! 

CAUTION: TO REDUCE THE RISK OF ELECTRICAL
SHOCK, DO NOT OPEN COVERS. NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.

This label may appear on the bottom of the unit due to space limitations.

The lightning flash with an arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.

The exclamation point within an equilateral triangle is intended to
alert the user to presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.

Warning

To prevent fire or shock hazard, do not expose units not
specifically designed for outdoor use to rain or moisture.

Attention: Installation should be performed by qualified service
personnel only in accordance with the National Electrical Code or
applicable local codes.

Power Disconnect. Units with or without ON-OFF switches
have power supplied to the unit whenever the power cord is
inserted into the power source; however, the unit is operational
only when the ON-OFF switch is in the ON position. The power
cord is the main power disconnect for all units.

External Power Supplies

Use only the Recommended Power Supplies.  Power
supplies must comply with the requirements of the latest version
of IEC 65/VDE 0860. Substitutions may damage the unit or cause
a fire or shock hazard.

SECURITE

ATTENTION

RISQUE D'ELECTROCUTION.

NE PAS OUVRIR.

Danger: Pour éviter tout risque d'électrocution, ne pas
ouvrir le boîtier. Il n'y a pas de pièces remplaçables à
l'intérieur. Pour toute révision, s'adresser à un technicien
spécialisé.

En raison de limitation de place, cette étiquette peut être placée sur le
dessous de l'appareil.

L'éclair fléché dans un triangle équilatéral, avertit l'utilisateur de la
présence d'une "tension dangereuse" non isolée à l'intérieur de
l'appareil et d'une valeur suffisante pour constituer un risque
d'électrocution.

Le point d'exclamation contenu dans un triangle équilatéral,
avertit l'utilisateur de la présence, dans la documentation qui
accompagne l'appareil, de consignes d'utilisation et de
maintenance importantes.

Attention

Pour éviter le risque d'électrocution ou d'incendie, ne pas
exposer à la pluie ou à l'humidité un appareil non conçu pour
une utilisation extérieure

.

Attention: L'installation doit être effectuée uniquement par du
personnel de service qualifié conformément à la réglementation
du Code Electrique National ou à la réglementation locale.

Disjonction de l'alimentation. Les appareils avec ou sans
commutateurs ON-OFF sont alimentés à chaque fois que le
cordon d'alimentation est branché à la source d'alimentation;
toutefois, les appareils disposant de commutateurs ON-OFF ne
fonctionnnent que lorsque le commutateur ON-OFF est sur la
position ON. Le cordon d'alimentation est la disjonction
d'alimentation principale pour tous les appareils.

Sources d'alimentation extérieures

Utiliser uniquement les sources d'alimentation
recommandées. 
Les sources d'alimentation doivent être
conformes aux réglementations de la dernière version IEC
65/VDE 0860. Toute modification peut endommager l'appareil ou
provoquer un incendie ou un choc électrique.

Summary of Contents for LTC 5104 Series

















Reviews: