background image

4

5

EN

EN

3 Connect

This section helps you connect your SoundBar 

to a TV and other devices. 

For information about the basic connections of 

your SoundBar and accessories, see the quick 

start guide. 

Note

 

For identification and supply ratings, refer to the type 

plate at the back or bottom of the product.

 

Before you make or change any connections, make sure 

that all devices are disconnected from the power outlet.

Placement

Place the subwoofer at least 1 meter (3 feet) 

away from your SoundBar, and ten centimeters 

away from the wall.

For best results, place your subwoofer as shown 

below.

 

Connect audio from TV and 

other devices

Play audio from TV or other devices through 

your Soundbar speakers.

Use the best quality connection available on 

your TV, Soundbar, and other devices. 

Option 1: Connect audio through a 

digital optical cable

Best quality audio 

 

Using an optical cable, connect the 

OPTICAL

 connector on your SoundBar to 

the 

OPTICAL OUT

 connector on the TV 

or other device. 

•  The digital optical connector might be 

labeled 

SPDIF

 or 

SPDIF OUT

Option 2: Connect audio through a 

digital coaxial cable

Best quality audio 

 

Using a coaxial cable, connect the 

COAXIAL

 connector on your SoundBar 

to the 

COAXIAL/DIGITAL OUT

 

connector on the TV or other device. 

TV

 (Standby-On) 

Switch the SoundBar on or to standby.

AUX

Switch your audio source to the AUX 

connection. 

AUDIO-IN

Switch your audio source to audio input 

connection (3.5mm jack).

+/-

Increase or decrease volume.

USB

Switch your audio source to the USB 

connection.

SURR

Toggle between stereo and virtual 

surround sound.

BASS +/- / RESET

•  Increase or decrease bass.

•  Reset your bass level to the default 

settings programmed at the factory.

/- / RESET

•  Increase or decrease treble.

•  Reset your treble level to the default 

settings programmed at the factory.

OPT

Switch your audio source to the optical 

connection. 

Mute or restore volume.

COAX

Switch your audio source to the coaxial 

connection. 

Connectors

This section includes an overview of the 

connectors available on your SoundBar.

Top connectors

  

 (USB)

Audio input from a USB storage device.

AUDIO-IN

Audio input from an MP3 player (3.5mm 

jack).

Rear connectors

 

AUDIO IN

Connect to an analog audio output on the 

TV or an analog device. 

DIGITAL IN-COAXIAL

Connect to a coaxial audio output on the 

TV or a digital device. 

DIGITAL IN-OPTICAL

Connect to an optical audio output on the 

TV or a digital device. 

SUBWOOFER

Connect to the supplied subwoofer.

AC MAINS~

Connect to the power supply.

b

a

e

a

d

b

c

Summary of Contents for HTL2151/F7










Reviews: