Philips HD7761/00 Service Manual Download Page 3

Page: 3 / 15

HD7761/00 /C

3-15

TECHNICAL INFORMATION

Self-Check mode

The appliance is equipped with a self-check mode, this enables you to quickly check the function of the main components of
the unit.

Keep the On/Off button pressed while
plugging the mains cord into the socket.

Left side display

Hardware version

Press

any other

button

Software version

Press

any other

button

Heating element enabled

Press

any other

button

Heating element disabled

Press

any other

button

Grinder motor enabled

Press

any other

button

Grinder motor di 6 Beeps

Press

any other

button

Microcontroller check

Press

any other

button

Zero-cross detection

Press

any other

button

Valve micro switches

Press

any other

button

Inspection window micro switch

Press

any other

button

Thermostat

Press

any other

button

Rotary knob

Press

any other

button

Rotary knob rotate clockwise

Increasing

Rotary knob rotate anti-clockwise

Decreasing

LED check

All digits on (Left side only)

Press

any other

button

LED check

All digits off

Press

On/Off

button

Stand-by

Summary of Contents for HD7761/00
















Search results

Summary of Contents for HD7761/00

Reviews:

Related manuals for HD7761/00

Brands by name

Popular brands

Philips HD7761/00, Service Manual

Search results

Summary of Contents for HD7761/00

Reviews:

Related manuals for HD7761/00

Brands by name

Popular brands