Philips DVD 620, Service Manual, Page: 33 / 59

Diagnostic Software Descriptions and Troubleshooting EN 33 DVD 620 /0X1 5.
5.8.4 Processor & Peripherals Nuclei
5.8.5 Log Nuclei
5.8.6 Miscellaneous Nuclei
6001 “No readback on P50”
6002 “Disp not responding “
6003 “P50 readback error”
Error
code
Error text
700 Test successful
720 Test successful
740 Test successful
600 "All checksums are correct"
601 “Following checksum is faulty: BootCode1
Checksum is 0xY2 and is not correct (must be
0xZ2)”
601 “This test is not available when stand-alone
compiled”
6200 "Checksums = 0xA1, 0xB1, 0xC1, 0xD1"
6201 “This test is not available when stand-alone
compiled”
1000 Test successful
1001 Test successful
1020 Test successful
1021 Test successful
1100 Test successful
1104 “NVRAM reply time-out”
1200 Test successful
1202 “Slave bus not working”
1203 “Slave controller not responding”
1204 “Slave response is not correct”
5900 Test successful
5901 “I2c bus busy”
5902 “I2c bus not working“
5904 “DTS chip response not correct”
1300 Test successful
1301 “Parity error from basic engine to serial”
1302 “Parity error from serial to basic engine”
1303 “No communication between serial and basic
engine”
1304 “Communication time-out error”
1600 Test successful
1601 “The DVD SDRAM is faulty”
Error
code
Error text
3100 "Show error log"
3101 "Error log is invalid"
3102 "Error log could not be read from NVRAM"
3103 "I2C bus busy before start"
3200 "Show error bit"
3201 "Error log is invalid"
3202 "I2C bus busy before start"
Error
code
Error text
3203 "Error log could not be read from NVRAM"
3300 "Error log is cleared"
3301 "Error log could not be cleared"
3302 "I2C bus busy before start"
Error
code
Error text
3400 Test successful
3401 “The configuration data could not be read
from NVRAM”
3402 “I2C bus busy before start”
3500 “NVRAM is cleared”
3501 “The NVRAM could not be reset.”
3502 “I2C bus busy before start”
3600 “NVRAM contents updated.”
“NVRAM contents and configuration
checksum updated.”
3601 “NVRAM contents could not be updated.”
3602 “I2C bus busy before start”
3603 “NVRAM contents could not be read”
3604 “NVRAM not accessible.”
3605 “NVRAM checksum could not be updated.”
1500 Test successful
1502 “NVRAM access time-out”
1504 “NVRAM fails”
5400 Test successful
5401 “I2c bus busy”
5402 “I2c bus not working“
5403 “Scart switch controller not responding”
5404 “Scart switch controller response not correct”
5500 Test successful
5501 “I2c bus busy”
5502 “I2c bus not working“
5520 Test successful
5521 “I2c bus busy”
5522 “I2c bus not working“
5523 “Scart switch controller not responding”
5200 Test successful
5201 “I2c bus busy”
5202 “I2c bus not working“
5300 Test successful
5301 “I2c bus busy”
5302 “I2c bus not working“
5320 Test successful
5321 “I2c bus busy”
5322 “I2c bus not working“
4700 “Number of times Tray went Open : XX”
4701 The total number of times tray went open
could not be read from NVRAM.
4702 I2C bus busy before start
Error
code
Error text