background image

Domestic Appliances and Personal Care

HQ 5660/A

CoolSkin

Rechargeable shaver

Published by Philips Domestic Appliances and Personal Care     Printed in The Netherlands      Copyright reserved     Subject to modification

©

98/09

4822 729 21977

PCS 99 514

GENERAL

-  Cool skin is a new shaving system.
   The shaver features a special compartment for 

cartridges containing Nivea for Men  moisturising 
shaving emulsion.

   This emulsion is applied to the skin while shaving.
- The shaving unit can be cleaned under a running hot 

tap.

   The HQ156 shaving heads are made of special
   stainless steel for corrosion-free cleaning with water.
-  The shaver has a separate trimmer for grooming 

sideburns and moustaches.

   The trimmer can be flipped open to enable cleaning
   of the inside.
-  The charging stand of the shaver can be placed on a flat 

surface or it can be attached to the wall.

   The PCB inside is encased in insulating material.
   For this reason the mains cord cannot be replaced if it is 

damaged.

TECHNICAL DATA

Input voltage 

:  100-240 V, 50/60Hz

Motor voltage     

:  2.4 V

Cell             

:  2X 4/5AA NiMH

Cell capacity  

:  approx. 1000 mAH

Charging indicators  :  duoLED red/green
Charging time     

:  approx. 1 hour

Charging current  

:  1000/100/25 mA time-dependent

Charging device   

:  Switched Mode Power Supply in 

stand

                    

in  : 100-240 

                    

out : 12-17 V 

Comfort control   

:  fixed setting

                    

   contour following

Shaving heads     

:  HQ156 - 4822 690 10152

Shaving emulsion   :  HQ150 - 4822 390 10156 W-EU

MSH Coding
8855 660 00000 HQ 5660

!

Service

Information

!

Service

Information

Summary of Contents for CoolSkin HQ 5660

Page 1: ...rimmer for grooming sideburns and moustaches The trimmer can be flipped open to enable cleaning of the inside The charging stand of the shaver can be placed on a flat surface or it can be attached to the wall The PCB inside is encased in insulating material For this reason the mains cord cannot be replaced if it is damaged TECHNICAL DATA Input voltage 100 240 V 50 60Hz Motor voltage 2 4 V Cell 2X ...

Page 2: ...2 361 21783 motor 2 4V 11 4822 441 12221 housing 12 4822 214 12791 power module 13 4822 492 11614 contact spring 14 4822 256 10454 holder 15 4822 463 11187 pump slide 16 4822 442 01482 cover 17 4822 479 20198 cleaning brush 18 4822 690 10176 trimmer complete 19 4822 466 91312 foam plate 20 4822 256 10455 battery holder 21 4822 138 10672 NiMH pack 4 5AA 22 4822 360 10389 pump 23 4822 442 01481 slid...

Page 3: ... 1 hour the green LED starts blinking and the charging current is reduced to 100 mA It is kept at this level during the next 2 hours Then charging continues at 25mA The cells are charged at fixed currents via switching transistor TS1 The current is detected by sense resistor R9 The timers in IC1 adjust the current level via the enable signal at pin 2 by regulating the conductive time of TS1 b Elec...

Page 4: ...1 IC1 1 23 22 2 24 12 13 4 3 11 7 6 5 10 8 R13 R11 R14 R15 R16 C3 C6 C4 C5 9 R20 D5 Vdd TS2 TS1 R1 1 2 3 1 8 9 1 11 12 M R12 R17 R19 R18 t D3 100 240V 50 60Hz C1 R1 L1 C2 C12 R12a R5 R8 R1 TS3 TS2 TS4 TS6 TS7 TS1 R17 R14 R16 R6 R7 R9 R15 R4 R19 C3 R18 R3 R10 R2b R2a TS5 R12b R13 C8 D4 C7 C4 C13 C6 C5 C10 C9 D5 D6 D2 D1 D7 ...

Reviews: