2
Quick Install Guide - Philips CertaFlux RDL vertical
September 2018
Important
Please take the time to read this installation guide before you install this Philips LED product and driver.
The guide contains important information regarding installation and operation.
Warranty
Warranty only applies when the appropriate Philips LED driver and Philips cabling (as described in this guide and leaflets) are used.
Please visit our website www.philips.com/ledrefrigeration or contact your local sales office for more information.
Warnings
• The installation guide does not supersede local or (inter)national regulations for electrical installations.
• This Philips LED product and LED driver must be installed by a professional electrician in accordance with the applicable and
• appropriate electrical codes and the instructions provided by Philips.
• This Philips LED product is designed to be connected to a circuit from a class 2 /SELV power source (Philips constant voltage LED
driver) with energy-limited supply. For maximum system efficacy, load the driver to 90%.
• This is a 24 V DC product. Please ensure proper routing of the cable to avoid cable damage.
• Do not connect this LED product to mains voltages.
• To allow for variance in the installation, it is not recommended to load the Philips LED driver beyond 90% of its rated maximum power.
• The energy consumption of the engine is a nominal value, with an estimated 20% deviation.
• Before installation, maintenance or cleaning, always first switch off or disconnect the power and follow the appropriate safety
procedures.
• The module and mounting profile shall be installed at distances more than 3 mm from the current-carrying parts of the appliance.
• Do not use tape to fix this LED product or LED profile in position; please use the appropriate mounting clips.
• Please note that the colors of the wires in existing designs, such as refrigeration systems or cabinets, may differ. The position of the
• (original) ballast may also differ.
• Do not make sharp bends with electrical wires.
• For UL region only: CAUTION: To reduce the risk of fire, do not install in a compartment smaller than 11.8 inches (30 cm) by
11.8 inches (30 cm) by length of luminaire.
• Due to the variety of designs and brands in which the Philips LED products can be installed, you may need to use customized
mounting accessories to fit the specific design you are using. If you require further support, please contact your local Philips sales
organization.
• Philips advises using a zero-crossing/switching solid-state relay to reduce the inrush current peak.
• This product is designed for damp and dry locations only.
Cleaning
• Use a damp cloth and a mild cleaning agent. Do not wipe the LED product with a dirty or very wet dishcloth or towel because they may
leave residue that can damage the LED product.
• Do not use abrasive cleaners, scouring pads, bleach or cleaners containing chlorine because they can scratch and damage the LED
product.
Maximum allowed number of drivers per circuit breaker
12nc
B10
B16
C6
C10
C16
Imax (A)
Period (ms)
LED Power driver 100W-24V
929001430080
3
6
4
6
10
38
480
LED Power driver 80W - 24V *
929000653906
2
5
3
6
10
100
150
LED Power driver 20W - 24V *
929000654006
8
15
8
16
28
50
180
* The LED engine system powered by this driver is Compliant to IEC 60335 standard (Household and similar electrical appliances)
• These values are indicative and shall not take the place of local and (inter) national regulations for electrical installations.
• This table only applies to the specified Philips driver.
• The data in this table are indicative, the installer must take into account external factors. External factors beyond the control of Philips
Lighting (eg cable length, mix of products on the circuit breaker, ...)
• Note that the maximum number of drivers is given for a situation in which this all be connected at the same time, for example via a wall
switch.
System disposal
We recommend that the CertaFlux RDL module and its components are disposed of in an appropriate way at the end of their (economic)
lifetime. The modules are in effect normal pieces of electronic equipment containing components that are currently not considered to be
harmful to the environment. We therefore recommend that these parts are disposed of as normal electronic waste, in accordance with
local regulations.