background image

Power Supply

General Operation/Radio

•  Incorrect use of batteries can cause 

electrolyte leakage and will corrode the 
compartment or cause the batteries to burst

:

•  Do not mix battery types: e.g. alkaline with 

carbon zinc. Only use batteries of the same
type for the set.

•  When inserting new batteries, do not try to mix

old batteries with the new ones.

•  Remove the batteries if the set is not to be

used for a long time.

Using AC  power

WARNING: Always check you have com-

pletely switched off the set, before you

change or disconnect power supply.

Check if the power voltage,

as shown on

the type plate located on the 
bottom of the set,

corresponds to your

local power supply. If it does not, consult your
dealer or service center.

Connect the power cord to the 

AC ~

inlet

and the wall outlet.The power cord is now 
connected and ready for use.

To switch the set off completely, withdraw
the power cord from the wall socket.

4

Install the unit near the AC outlet and where
the AC power plug can be easily reached.

Disconnect the power cord from the wall
socket to protect your set during heavy 
thunderstorms.

The model and serial numbers are 

located on the bottom of the set.

Helpful hints:

–  

To avoid unnecessary energy consumption,

always adjust 

FUNCTION

to 

TAPE/ OFF

after using the set. Also check that the tape

deck keys are released.

General operation

To select your sound source, adjust

FUNCTION

to:

CD

,

TAPE/ OFF

or

RADIO.

2

To switch off the set, adjust the source 
selector to 

TAPE/ OFF

position and check

the cassette keys are released.

Adjusting volume and sound

Adjust the sound with the 

VOL

and 

DBB

controls.

Radio reception

Adjust 

FUNCTION

to 

RADIO

.

Adjust 

BAND

to select your desired 

waveband,

MW

,

FM 

or 

FM STEREO

3

Turn 

TUNING

to tune to a station.

FM STEREO

lights up for stereo FM

reception.

To improve radio reception:

For 

FM

, extend and turn the telescopic

antenna for best reception. Reduce its length
if the signal is too strong.

To tune to a weak FM station, adjust 

BAND

to 

FM

(mono).

For 

MW

, the set uses a built-in antenna.

Direct this antenna for best reception by
turning the whole set.

AZ1019_61_Eng_CCR  5/8/08  9:47  Page 7

Summary of Contents for AZ1019













Reviews: