English
Controls/Power Supply
Power Supply
General Operation/Tuner
• Incorrect use of batteries can cause
electrolyte leakage and will corrode the
compartment or cause the batteries to burst
:
• Do not mix battery types: e.g. alkaline with car-
bon zinc. Only use batteries of the same type
for the set.
• When inserting new batteries, do not try to mix
old batteries with the new ones.
• Remove the batteries if the set is not to be
used for a long time.
Using AC power
WARNING: Always check you have
completely switched off the set, before you
change or disconnect power supply.
1
Check if the power voltage,
as shown on
the type plate located on the
bottom of the set,
corresponds to your
local power supply. If it does not, consult your
dealer or service center.
2
If your set is equipped with a voltage selector,
adjust the selector so that it matches with the
local mains.
3
Connect the power cord to the
AC ~
inlet
and the wall socket.The power cord is now
connected and ready for use.
4
To switch the set off completely, withdraw
the power cord from the wall socket.
•
Disconnect the power cord from the wall
socket to protect your set during heavy
thunderstorms.
The type plate are located on the
bottom of the set.
Helpful hints:
–
To avoid unnecessary energy consumption,
always adjust the
Source selector
to
TAPE/ OFF
after using the set. Also check
that the tape deck keys are released.
General operation
1
To select your sound source, adjust the
Source selector
to:
CD
,
TUNER
or
TAPE/ OFF.
2
To switch off the set, adjust the
Source
selector
to
TAPE/ OFF
position and
check the cassette keys are released.
Adjusting volume and sound
Adjust the sound with the
VOLUME
and
BASS BOOST
controls.
Radio reception
1
Adjust the
Source selector
to
TUNER
.
2
Adjust
BAND
to select your desired
waveband,
AM (MW)
or
FM ST.
(stereo)
3
Turn
TUNING
to tune to a station.
-
STEREO
indicator lights up for stereo FM
reception.
To improve radio reception:
•
For
FM
, extend and turn the telescopic
antenna for best reception. Reduce its length
if the signal is too strong.
To tune to a weak FM station, adjust
BAND
to
FM
(mono).
•
For
AM (MW)
, the set uses a built-in anten-
na. Direct this antenna for best reception by
turning the whole set.
Supplied Accessories
– AC power cord
Top and front panels (See
1
)
1
VOLUME
– adjusts volume level.
2
BASS BOOST
– turns the bass enhance-
ment on/off.
3
Source selector
:
CD,TUNER,TAPE/OFF
– selects CD, radio or tape source of sound
– power off switch
4
BAND
– selects waveband
5
TUNING
– tunes to radio stations
6
LIFT TO OPEN
– opens/ closes the CD
door.
7
CASSETTE RECORDER keys:
PAUSE
– pauses playback or recording
STOP•EJECT
– stops the tape;
– opens the cassette holder.
F.FWD/ REW
– fast winds/ rewinds tape;
PLAY
– starts playback;
REC
– starts recording.
8
PROG
– programs tracks and reviews the
program
9
.
2
/
;
PLAY/PAUSE
– starts or pauses CD
playback.
0
9
STOP
– stops CD playback;;
– erases a CD program
!
REPEAT
– repeats a track/
CD program/entire CD.
@
Display
– shows the CD functions
#
STEREO indicator
– lights up for stereo
FM reception
.
$
SEARCH
∞
,
§
– skips or searches a
passage/track backwards or forward
%
POWER indicator
– lights up when the
set is powered on.
Back panel (See
2
)
^
Telescopic antenna
- improves FM
reception.
&
p
– 3.5 mm stereo headphone socket
Helpful hints:
The speakers will be muted
when headphones are connected to the set.
*
AC ~
- inlet for power cord.
(
Battery door
- open to insert
6
x 1.5V
R-14
/
UM2
/
C-cells
.
)
Voltage selector
– (inside the battery
compartment, not all versions) adjust to
match the local voltage 110/220V before
plugging in the set.
CAUTION
Use of controls or adjustments or per-
formance of procedures other than
herein may result in unsafe operation.
Power Supply
Whenever convenient, use the power supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
Batteries (not included)
1
Open the battery compartment and insert
6
batteries, type
R-14
,
UM-2
or
C-cells
,
(preferably alkaline) with the correct polarity
as indicated by the "
+
" and "
–
" symbols inside
the compartment. (See
2
)
2
Replace the compartment door, making sure
the batteries are firmly and correctly in place.
The set is now ready to operate.
Batteries contain chemical substances, so
they should be disposed of properly.
