Philips AX6301, Service Manual, Page: 4 / 20

1-3
POWER SUPPLY/GENERAL INFORMATION
Batteries (not included)
Inserting batteries
• Open the battery compartment and insert 2 alka-
line batteries of type AA ( LR6 , UM3 ).
• When using the remote control for the first time,
please remove the clear protective tab from the
battery.
• Do not mix old and new or different types of batteries.
Indication of empty batteries
• Replace the batteries or connect the mains adapter as soon as
.
blinks.
• Remove batteries if they are empty or the set will not be used for a long time.
Average playing time of batteries under normal conditions
Alkaline battery
ESP on ESP off
VCD 3 hours 3.5 hours
CD 7 hours 7.5 hours
MP3-CD 9.5 hours
Batteries contain chemical substances, so they should be disposed of
properly.
Mains adapter (supplied AY3193)
Use only the AY3193 adapter (DC: 4.5V/800mA; AC:
110V/220V and 50/60Hz). Any other product may
damage the player.
1
Make sure the mains voltage matches the voltage
requirement of the mains adapter.
2
Connect the mains adapter to the 4.5V DC socket of
the player and to the wall socket.
PLAYBACK
Playing a disc
With this set, you can play
- Video discs
- audio discs (pre-recorded audio CDs, finalized audio
CDs and CD-RWs)
- MP3-CDs (CD-ROMs with MP3 files)
For VCD playback, you need to connect the player to
your TV (see Connecting to your TV system)
1 Push the OPEN
2
slider to open the disc lid.
2 Insert a disc, printed side up, by pressing the CD onto
the hub. Close the lid by pressing the lid down.
3 Press
2;
on the set to start playback.
Playback starts
.
Video disc: appears. The current track number
and the elapsed time are displayed.
Audio disc: The current track number and the elapsed
playing time are displayed.
MP3-CD: MP3 appears. The current album number, track number and the
elapsed playing time are displayed.
4
To stop playback, press
9
.
Video disc: The number of tracks and the total playing time of the disc are
displayed.
Audio disc: The number of tracks and the total playing time of the disc are
displayed.
MP3-CD: The number of albums and the number of tracks are displayed.
.
TIP:
-
Always disconnect the adapter when you are not using it.
- Once the mains adapter is connected, the power supply from batteries will
be switched off automatically.
TV connection
Connecting to your TV System
Use the supplied AV cable to connect the player to your TV system. To ensure
uninterrupted viewing, we recommend you use AC mains power for your play-
er during VCD operation.
1
Insert the yellow video cable pin into the VIDEO IN jack on the rear of your TV.
Insert the white and red audio cable pins respectively into the left and right
AUDIO IN jacks of your TV.
2
Insert the pin on the other end of the AV cable into the LINE OUT jack on
your player.
3
Connect the mains adapter to the 4.5V DC socket of the player and to the wall
socket.
LINE OUT p
Playing a disc
5 Press
9
again to switch off the player.
• To remove the disc, hold it by its edge and press the hub
gently while lifting the disc.
TIP:
- Y ou can only press
2;
on the set to start
playback.
- i f there is no activity, the player will automatically switch off in 30 seconds to
save energy.
-
After pressing
2;
,
you may need to wait for 10 seconds or more until the
first MP3 track is played.
Pause
1
Press
2;
to interrupt playback.
The track number and the elapsed playing time are displayed.
2
Press
2;
again to resume playback
TIP:
- If the set stays in the PAUSE mode for more than 90 seconds, it will enter the
STOP mode automatically. After 30 seconds or more in the STOP mode, your
set automatically powers down.
0
INSTRUCTION FOR USE