1-6
Troubleshooting
No sound or bad sound quality.
• PAUSE might be active. Press
2;
.
• Loose, wrong or dirty connections. Check and clean connections.
• Volume might not be appropriately adjusted. Adjust the volume.
• Strong magnetic fields. Check player’s position and connections. Also keep
away from active mobile phones.
• For in-car use, check that the cassette adapter is inserted correctly, that the car
cassette player’s playback direction is correct (press autoreverse to change),
and that the cigarette lighter jack is clean. Allow time for temperature change.
RESUME and HOLD
You can interrupt playback and continue (even after an
extended period of time) from the position where
playback stopped (RESUME) and you can lock all buttons
of the set so that no action will be executed (HOLD).
Use the RESUME–HOLD–OFF slider for these functions.
RESUME – continuing from where you have stopped
1
Switch the slider to RESUME during playback to activate RESUME.
y
resume
is shown.
2
Press
9
whenever you want to stop playback.
3
Press
2;
whenever you want to resume playback.
y
resume
is shown and playback continues
from where you have stopped.
• To deactivate RESUME, switch the slider to OFF.
y
resume
goes off.
HOLD – locking all buttons
You can lock the buttons of the set by switching the slider to HOLD. Now, when a
key is pressed, no action will be executed. This is of use, for example, when
transporting the player in a bag. With HOLD activated, you can avoid accidental
activation of other functions.
1
Switch the slider to HOLD to activate HOLD.
y
All buttons are locked.
HoLd
is shown when
you press any button. If the set is switched off,
hold
will be shown only when
2;
is pressed.
2
To deactivate HOLD, switch the slider to OFF.
Note: If you deactivate HOLD by switching the slider to RESUME, you will be
activating the RESUME function.
FEATURES
Selecting different playing possibilities
−
MODE
It is possible to play tracks in random order, to repeat a single track or the entire
CD, and to play the first few seconds of each track.
1
Press MODE during playback as often as required in
order to activate one of the following ‘modes’. The
active mode is shown in the display.
y
shuffle
: All tracks of the CD are played in
random order until all of them have been played
once.
y
shuffle repeat all
: All tracks of the CD
are played repeatedly in random order.
y
repeat
:
The current track is played repeatedly.
y
repeat all
: The entire CD is played repeatedly.
y
SCAN
: The first 10 seconds of each of the
remaining tracks are played in sequence.
2
Playback starts in the chosen mode after 2 seconds.
• To return to normal playback, press MODE repeatedly until the display shows
no active modes.
ESP / Power Save Mode
With a conventional portable CD-player you might have experienced that the
music stopped e.g. when you were jogging. The
E
LECTRONIC
S
KIP
P
ROTECTION
prevents loss of sound caused by light vibrations and shocks. Continuous playback
is ensured. However ESP does not prevent playback interruptions during vigorous
running. It also does not protect the unit against any damage caused by dropping!
On this set ESP is default on. It is possible to set ESP off and enter the Power
Save mode. The Power Save mode helps to extend battery lifetime for longer
playback.
• Press MODE for more than 2 seconds.
y
disappears. Power save mode is now activated.
• Press MODE again for more than 2 seconds.
y
is displayed once
ESP on
➟
Power Save
➟
ESP on
resume
resume
hold
TROUBLESHOOTING
Troubleshooting
WARNING:
Under no circumstances should you try to repair the set yourself as
this will invalidate the warranty. If a fault occurs, first check the points listed,
before taking the unit for repair. If you are unable to solve a problem by following
these hints, consult your dealer or service center.
The CD player has no power, or playback does not start
• Check that your batteries are not dead or empty, that they are inserted
correctly, that the contact pins are clean.
• Your adapter connection may be loose. Connect it securely.
• For in-car use, check that the car ignition is on. Also check player’s batteries.
The indication
no diSC
is displayed
• Check that the CD is clean and correctly inserted (label-side upward).
• If your lens has steamed up, wait a few minutes for this to clear.
The indication
nF diSC
is displayed
• CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.
The indication
HOLD
is on and/or there is no reaction to controls
• If HOLD is activated, then deactivate it.
• Electrostatic discharge. Disconnect power or remove batteries for a few seconds.
The CD skips tracks
• The CD is damaged or dirty. Replace or clean the CD.
• RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on.
CAUTION
Use of controls or adjustments or performance of procedures other than
herein may result in hazardous radiation exposure or other unsafe
operation.
repeat all
shuffle
INSTRUCTION FOR USE
