FEATURES
You can store up to 30 tracks to play in a program.
A single track may be stored more than once in the
program.
1
While playback is stopped, select a track with
∞
or
§
.
2
Press PROG to store the track.
y
PROG
lights up; the track number
programmed and
P
with the total number of
stored tracks are displayed.
3
Select and store all desired tracks in this way.
4
Press
2;
to start playback of your selected tracks.
y
PROG
is shown and playback starts.
• You can review the program by pressing PROG for
more than 2 seconds.
y
The display shows all the stored tracks in sequence.
Notes: – If you press PROG and there is no track select-
ed,
noProg
is displayed.
– If you try to store more than 30 tracks,
FULL
is displayed.
Clearing the program
• While playback is stopped, press
9
to clear program.
y
CLEAr
is displayed once,
PROG
goes off, and
the program is cleared.
Note:
The program will also be cleared if the power supply is interrupted, or if
the CD-player lid is opened, or if the set switches off automatically.
Programming track numbers
FEATURES / TROUBLESHOOTING
You can interrupt playback and continue (after up to 1 minute in the disc stop
position only) from the position where playback stopped (RESUME) You can
lock all buttons of the set so that no action will be executed (HOLD). Use the
RESUME–HOLD–OFF slider for these functions.
RESUME – continuing from where you have stopped
1
Switch the slider to RESUME during playback to acti-
vate RESUME.
y
RESUME
is shown.
2
Press
9
whenever you want to stop playback.
3
Press
2;
whenever you want to resume playback.
y
RESUME
is shown and playback continues from
where you have stopped.
• To deactivate RESUME, switch the slider to OFF.
y
RESUME
goes off.
HOLD – locking all buttons
You can lock the buttons of the set by switching the slider to HOLD. Now, when a
key is pressed, no action will be executed. This is of use, for example, when
transporting the player in a bag. With HOLD activated, you can avoid accidental
activation of other functions.
1
Switch the slider to HOLD to activate HOLD.
y
All buttons are locked.
HoLd
is shown when
you press any button. If the set is switched off,
HOLD
will be shown only when
2;
is pressed.
2
To deactivate HOLD, switch the slider to OFF.
Note: If you deactivate HOLD by switching the slider to RESUME, you will be
activating the RESUME function.
RESUME and HOLD
It is possible to play tracks in random order, to repeat a single track or the entire
CD, and to play the first few seconds of each track.
1
Press MODE during playback as often as required in
order to activate one of the following ‘modes’. The
active mode is shown in the display.
y
SHUFFLE
: All tracks of the CD are played in
random order until all of them have been played
once.
y
SHUFFLE REPEAT ALL
: All tracks of the CD
are played repeatedly in random order.
y
REPEAT :
The current track is played repeatedly.
y
REPEAT ALL
:
The entire CD is played repeatedly.
y
SCAN
: The first 10 seconds of each of the
remaining tracks are played in sequence.
2
Playback starts in the chosen mode after 2 seconds.
• To return to normal playback, press MODE repeatedly until the display shows
no active modes.
ESP
With a conventional portable CD-player you might have experienced that the
music stopped e.g. when you were jogging. The
E
lectronic
S
kip
P
rotection
prevents loss of sound caused by light vibrations and shocks. Continuous playback
is ensured. However ESP does not prevent playback interruptions during vigorous
running. It also does not protect the unit against any damage caused by dropping!
In this set ESP is default ON. It is possible to set ESP off.
• Press MODE for more than 2 seconds.
y
ESP
disappears.
• Press MODE again for more than 2 seconds.
y
ESP
is displayed.
ESP on
➟
ESP off
➟
ESP on
Selecting different playing possibilities-MODE
WARNING:
Under no circumstances should you try to repair the set yourself as
this will invalidate the warranty. If a fault occurs, first check the points listed,
before taking the unit for repair. If you are unable to solve a problem by following
these hints, consult your dealer or service center.
The CD player has no power, or playback does not start
• Check that your batteries are not dead or empty, that they are inserted
correctly, that the contact pins are clean.
• Your adapter connection may be loose. Connect it securely.
• For in-car use, check that the car ignition is on. Also check player’s batteries.
The indication
no diSC
is displayed
• Check that the CD is clean and correctly inserted (label-side upward).
• If your lens has steamed up, wait a few minutes for this to clear.
The indication
nF diSC
is displayed
• CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.
The indication
HOLD
is on and/or there is no reaction to controls
• If HOLD is activated, then deactivate it.
• Electrostatic discharge. Disconnect power or remove batteries for a few seconds.
The CD skips tracks
• The CD is damaged or dirty. Replace or clean the CD.
• RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on.
No sound or bad sound quality.
• PAUSE might be active. Press
2;
.
• Loose, wrong or dirty connections. Check and clean connections.
• Volume might not be appropriately adjusted. Adjust the volume.
• Strong magnetic fields. Check player’s position and connections. Also keep
away from active mobile phones.
•
For in-car use,
check that the cassette adapter is inserted correctly, that the car
cassette player’s playback direction is correct (press autoreverse to change),
and that the cigarette lighter jack is clean. Allow time for temperature change.
Troubleshooting