3 - 1
1
2
3
4
5
6
7
8
9
0
!
@
#
$
%
^
&
^
TIME/ ALARM
-
toggle to set the times for the clock time, or alarm 1 or 2.
&
Display
- shows the clock / alarm times and status of the unit.
POWER SUPPL
Y
1.
Check if the power voltage, shown on the AC-DC adapter
plug, corresponds to your local power
supply
. If it does not, consult your dealer or service cen-
ter
.
2.
Connect the AC-DC adapter plug to the wall outlet.
3.
To disconnect the set completely from the power supply
,
withdraw the AC-DC adapter plug from the wall outlet.
The serial and production number are located on the
bottom of the set.
Standby power consumption
(clock mode)
..........2W
MEMOR
Y BACKUP
The memory backup conveniently allows your clock and alarm
time settings to be stored for up to 3 minutes when there is a
power interruption e.g. AC power failure.
The complete CD clock radio and lighted display will be
switched off. As soon as the power supply returns, the display
will indicate the correct time.
•
If power supply returns after 3 minutes you will need to re-
enter the clock and alarm time settings.
BASIC FEA
TURES
Display brightness
1.
Toggle
REPEA
T ALARM/ BRIGHTNESS CONTROL.
y
The brightness of the display toggles between:
low
➟
bright
➟
low
V
olume
Press
4
or
3
to adjust the
volume level. The volume
level
uo
: is indicated as a number
from 0-32.
SETTING THE CLOCK AND ALARM TIMES
The time is displayed using the 12 hour clock (
PM indica-
tor
lights up = PM, off = AM).
1.
Press and hold down
TIME/
ALARM
until the clock or alarm
time display flashes, then
release
TIME/ ALARM
.
•
Press
TIME/ ALARM
repeatedly to toggle between the
time or alarm displays
2.
Press and hold down
∞
/
§
to fast adjust both the
hours and minutes settings.
3.
Release
∞
/
§
when you have reached the desired
setting.
y
If you need to adjust the time
slowly
, minute by minute,
press and release
∞
/
§
repeatedly
.
y
After several seconds, the time setting is
confirmed when the display stops flashing.
4.
Repeat steps 1-3 for each of the clock or alarm (
AL1,
AL2
) settings
.
CD PLA
YBACK
1.
Insert a CD with the printed side facing up, and close the
door
.
2.
Press
PLA
Y/ P
AUSE
2;
to start playback.
y
Display shows:
'
Cd
:
--
' and the total num-
ber of tracks, then your cur-
rent track number
, before
returning to clock time.
Other possible CD indications before
returning to clock time:
y
door
is shown if the CD door is not closed.
y
noCd
is shown if no CD has been inserted / insert-
ed incorrectly
.
y
nFCd
is shown if the CD-R(W) is non-
finalized
y
Err
indicates a general error in operation of the
set.
3.
Adjust the sound with
4
or
3
.
4.
To interrupt, press
2;
y
CD icon
flashes.
5.
Press
2;
again to resume playback.
6.
Press
ALARM RESET
to stop playback.
Note:
If CD playback is paused for more than 15
minutes and no controls are pressed, the set
automatically goes to standby mode.
CONTROLS
(see figure
1
)
1
AL 1 (
ALARM/ OFF)
-
selects CD alarm;
-
to cancel or switch off CD alarm.
2
W
AKE-UP TRACK
- to program to your favorite CD track for wake-up track
alarm option.
3
SLEEP
- adjusts timer options for CD / radio;
- switch on radio for timer mode.
4
REPEA
T ALARM/ BRIGHTNESS CONTROL
-changes the brightness of the display window;
-switches off the alarm for a 9 minute period;
-switches off radio / CD timer (SLEEP).
5
Power cord
-connect AC-DC adapter plug to wall outlet.
6
Coil antenna
-antenna to improve FM reception.
7
CD door
- lift here to open / close CD door
8
ALARM RESET (CD/ RADIO OFF)
- stops CD / radio playback;
- switches off radio / CD timer (SLEEP);
-
stops the active buzzer
, radio or CD alarms for 24 hours.
9
AL 2 (
ALARM/ OFF)
- selects radio
/ buzzer
alarm mode;
- to cancel or switch off radio / buzzer alarm.
0
VOLUME
3
,
4
- adjusts the sound level.
!
PLA
Y / P
AUSE
2;
- starts / pauses CD playback.
@
DOWN, UP
∞
,
§
- adjusts clock / alarm times
- skips CD tracks / searches for a particular passage.
#
Tuning indicator
- shows
the
radio
frequency
of
your
selected
waveband.
$
RADIO ON (FM/ AM)
- switches on the radio;
- selects the radio waveband.
%
TUNING
- tunes to a radio station.
1
Alarm time display
If you have set both alarms, the standby alarm time display
will show the earlier of the two alarm times as priority
.
E.g. if
AL1
= 6:00 and
AL2
= 5:45, then the standby alarm
display will show the
AL2
time 5:45.
INSTRUCTIONS FOR USE
www.freeservicemanuals.info
10/11/2012
www.nostatech.nl
World of free manuals
