RADIO
You can use this set solely as a radio!
1
Adjust
RADIO
OFF
/
ON
to
ON
to switch on the radio.
2
Select your waveband by adjusting the
BAND
switch.
3
Adjust
TUNING
to tune to your desired station.
4
Turn the
VOLUME
control to adjust the volume level.
5
Adjust
RADIO
OFF
/
ON
to
OFF
to switch off the radio.
To improve reception:
FM:
use the antenna built in the power cord. Adjust the position of the
power cord for optimum reception.
AM:
uses a built-in antenna inside the set. Direct the antenna by adjust-
ing the position of your set.
SETTING THE CLOCK AND ALARM TIMES
The time is displayed using the 12-hour clock with PM indicator (PM off = AM).
IMPORTANT!
To adjust the clock and alarm times accurately, always make sure
you press the
HR
or
MIN
buttons separately and not
simultaneously.
1
Turn the
clock control
to
SET TIME
or
SET ALARM
to set the clock or
alarm time respectively.
2
Press
HR
or
MIN
repeatedly or hold down on the respective button to adjust
the hours and minutes.
3
Release
HR
or
MIN
when you reach the correct setting.
4
After you have set both the hour and minutes, turn the
clock control
to
CLOCK
to run on clock time.
SELECTING THE ALARM MODE
GENERAL
If you wish to use the alarm, you must set the alarm time first. You can choose
from two different alarm modes to wake you up: by radio or buzzer.
• Select your choice of alarm mode by adjusting
ALARM
to
RAD
or
BUZ
.
™
If you have selected the radio mode, make sure you have adjusted the
volume loud enough to wake you.
™
The buzzer is set at a fixed volume and cannot be adjusted.
SWITCHING OFF THE ALARM
There are three ways of switching off the alarm. Unless you cancel the alarm
completely, the
24 hour alarm reset option
will be automatically selected after
1 hour and 59 minutes, from the time your alarm time first goes off.
24 HOUR ALARM RESET
If you want the alarm mode to be stopped immediately but also wish to retain the
same alarm setting for the following day:
• Press
ALARM RESET
during the alarm call.
CANCELING THE ALARM COMPLETELY
To cancel the set alarm time before it goes off, or during the alarm call:
• Adjust
ALARM
to
OFF
position.
REPEAT ALARM
This repeats your alarm call at 8-9-minute intervals.
1
During the alarm call, press
SLEEP OFF
/REPEAT ALARM
.
2
Repeat if desired for up to 1 hour and 59 minutes.
SLEEP
About Sleep
This set has a built-in timer which enables the set to be automatically switched
off during radio playback after a fixed period of 59 minutes. This allows you to lie
back, listen and fall asleep.
Setting SLEEP
1
Check that the
clock control
is in
CLOCK
position.
2
Set
RADIO
to OFF position.
3
Press
SLEEP
to activate the sleep function.
™
To cancel sleep, press
SLEEP OFF
/REPEAT ALARM
.
English
CONTROLS
1
PM indicator
- lights up when time is PM.
2
ALARM indicator
- lights up when alarm activated.
3
SLEEP
- activates the radio for sleep function
4
Clock control
-
CLOCK :
to run on clock time
-
SET ALARM :
sets the alarm time
-
SET TIME :
sets the clock time
-
HR/MIN :
adjusts the hours/ minutes for the clock and alarm times
5
SLEEP OFF
/REPEAT ALARM
- switches off the radio sleep function
- switches off the active alarm for a 8-9 minute period
6
Frequency indicator
- shows the radio frequency of your selected waveband
7
TUNING
- tunes to radio stations
8
BAND
- select FM/AM waveband
9
VOLUME
- adjusts the sound level
0
ALARM RESET
- stops the active alarm for 24 hours
!
DISPLAY
- show the clock/ alarm times and status of the set
@
RADIO
OFF
/
ON
- switches the radio off/on
#
ALARM
–
OFF
switches off the alarm
–
RAD
activates the radio for alarm
–
BUZ
activates the buzzer for alarm
$
Battery door
- opens to store a
9 volt 6F22
type battery (not included) for
clock memory backup
%
Power cord
- for power supply and to improve FM reception
INSTALLATION
POWER SUPPLY
1
Check if the power supply, as shown on the
type plate located on the bot-
tom of the set
, corresponds to your local power supply. If it does not, consult
your dealer or service center.
2
Connect the power cord to the wall outlet.
3
To disconnect the set from the power supply completely, remove the
plug from the wall outlet.
CLOCK MEMORY BACKUP
The clock memory backup allows your alarm and clock time settings to be stored
for up to a day when there is a power interruption e.g. power failure. The com-
plete clock radio and display illumination will be switched off. As soon as the
power supply returns, the display will indicate the correct time.
1
Remove the battery door to insert a
9 volt 6F22
type battery (not included) for
backup.
2
Replace the battery door.
NOTE:
If no backup battery is installed or the power interruption is prolonged, you
will need to set the clock and alarm times again.
Batteries contain chemical substances so should be disposed of
properly.
Standby power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1W
