Technical Specifications, Directions for Use, and Connections
2.
2.3.1
Side Connections
Smart Card Interface: Data Video - In/Out
Figure 2-2 Smart-card Connector
1
- 3V3 (1)
+3.3 V
k
2
- Ground power
Gnd
H
3
- 12V (1)
+12 V
j
4
- Ground I
2
C Gnd
H
5
- IR data
Data
j
6
- POR (2)
Signal
j
7
- TV Clock (3)
Clock Signal
k
8
- Data in (3)
Data
j
9
- Data out (3)
Data
k
10 - 5V (1)
+5 V
j
11 - H-sync Signal
k
12 - V-sync Signal
k
13 - Gnd CVBS in
Gnd
H
14 - SCL (4)
DDC clock
jk
15 - SDA (4)
DDC data
jk
16 - Reserved
17 - B_Pb in (5)
Blue in Signal
j
18 - G_Y in (5)
Green in Signal
j
19 - R_Pr in (5)
Red in Signal
j
20 - FBL in (5)
Signal
j
21 - Gnd CVBS out
Gnd
H
22 - CVBS out (6)
1 V
PP
/ 75 W
j
23 - Reserved
24 - Reserved
25 - Reserved
26 - Gnd Audio in
Gnd
H
27 - Audio R
0.5 V
RMS
/ 1 kW
k
28 - Audio L
0.5 V
RMS
/ 1 kW
k
29 - Audio R
0.5 V
RMS
/ 10 kW
j
30 - Audio L/Mono in 0.5 V
RMS
/ 10 kW
j
31 - Video CVBS/Yin 1 V
PP
/ 75 W
j
32 - C in
0.7 V
PP
/ 75 W
j
1.
Pin 1, 3, 10: maximum current limits 1.5A for 3.3V, 1.0A for
5V, and 0.6A for 12V. Total power may not exceed 10W.
2.
Pin 6: Bidirectional POR. TV will reset the system card
(active low) when mains is switched “off” to “on”. DCM can
reset iTV controller by pulling POR low for 150 ms.
3.
Pin 7, 8, 9: SPI bus global (either I2C bus or SPI at any one
time, not simultaneously).
4.
Pin 14, 15: I2C bus (either I2C bus or SPI at any one time,
not simultaneously).
5.
Pin 17, 18, 19, 20: RGB+FBL applicable only for full field
insertion and not for OSD. For CVI input, only applicable for
1fH.
6.
Pin 22: CVBS_terr_out when switching from analog RF to
SCART. Composite video out when switch from DVB-T to
SCART.
Head phone (Output)
Bk - Head phone
32 - 600 ohm / 10 mW
ot
Cinch: Video CVBS - In, Audio - In
Rd - Audio R
0.5 V
RMS
/ 10 kohm
jq
Wh - Audio L
0.5 V
RMS
/ 10 kohm
jq
Ye - Video CVBS
1 V
PP
/ 75 ohm
jq
S-Video (Hosiden): Video Y/C - In
1
- Ground Y
Gnd
H
2
- Ground C
Gnd
H
3
- Video Y
1 V
PP
/ 75 ohm
j
4
- Video C
0.3 V
PP
/ 75 ohm
j
USB2.0
Figure 2-3 USB (type A)
1
- +5V
k
2
- Data (-)
jk
3
- Data (+)
jk
4
- Ground Gnd
H
HDMI: Digital Video, Digital Audio - In
Figure 2-4 HDMI (type A) connector
1
- D2+ Data
channel
j
2
- Shield Gnd
H
3
- D2- Data
channel
j
4
- D1+ Data
channel
j
5
- Shield Gnd
H
6
- D1- Data
channel
j
7
- D0+ Data
channel
j
8
- Shield Gnd
H
9
- D0- Data
channel
j
10 - CLK+ Data
channel
j
11 - Shield Gnd
H
12 - CLK- Data
channel
j
13 - Easylink CEC
jk
14 - n.c.
15 - DDC_SCL DDC
clock
j
16 - DDC_SDA DDC
data
jk
17 - Ground Gnd
H
18 - +5V
j
19 - HPD
Hot Plug Detect
j
20 - Ground Gnd
H
Common Interface
68p - See diagram B09A
jk
2.3.2
Rear Connections
Mini Jack: Bathroom speaker (Output)
Bk - Bathroom speaker 8 W / 1 W
o
RJ48 DATA2 (Xpress Box/Set Top Box- In/Out)
1
- +12V +12V/1W
k
2
- Gnd Gnd
H
3
- Reserved
4
- Reserved
5
- TXD232 Signal
6
- RXD232 Signal
7
- IR-OUT/SDA Signal
k
8
- POR Signal
k
9
- CVBS_out Signal
k
10 - Gnd CVBS_out
Gnd
H
RJ12 DATA1 (SmartCard XPress Box)
1
17
16
3
2
10000_044_090121.ep
s
090121
Configure via communication menu
Pins SP-SPI
SP-Serial
XP
SP-I2C
HM-Link
1
SP Clock, 5V,
active low
Tx_ 5V,
active low
SCL, 5V,
active low
LED Ctrl
2
SP Data In, 5V,
active high
Rx_5V,
active low
Use pin 7 RJ45
for SDA, 5V
active low
IR in to TV, 5V,
active low
3
Reserved Reserved Reserved Reserved
4
SP Data Out, 5V,
active low
Not use
Not use
Status
1 2
3
4
10000_022_090121.ep
s
090121
10000_017_090121.ep
s
09042
8
19
1
1
8
2
