Alignments
8.
8.4
Setting the Correct iTV Mode
If the i-Board is directly replaced by a new off-the-shelf module
(already programmed with platform software), the correct iTV
model still must be programmed via below sequences to get to
the correct model type with its I/O configurations.
1.
Put the iTV remote control (e.g. RC2573) in setup mode.
2.
Push a number on the remote control to switch “on” the TV.
3.
Push the RECALL button.
4.
Check the model number, listed in line 05.
If the setting is correct, changing is not needed.
If the number is incorrect, continue with the next steps.
When the number is incorrect, proceed with the following
steps:
5.
Enter “042420”, immediately followed by “M” (Menu) key.
You now enter SDM.
6.
Select and activate NVM EDIT mode.
7.
Key in address “0022” (hex).
8.
Push the “ARROW DOWN” button to activate the “Value”
line.
9.
From the Diversity table read the diversity code that
belongs to the type of TV set you are adjusting. Enter that
number in the “Value” line.
10. Select STORE to put the new value in the NVM.
11. Push the POWER button to switch “off” the TV set.
12. Pull the mains plug.
13. Reconnect the mains plug after a few seconds.
14. The new setting is now active.
Table 8-3 Diversity table
8.5
Wireless Smart-Loader (22AV1120/00)
8.5.1
iTV Installation Tool
The Philips Wireless Smart-Loader is an installation tool
especially designed for easy and fast installation of Philips
Institutional TV's. The Wireless Smart-Loader 22AV1120/00 is
compatible with the Wired Smart-Loader version 22AV1015/
01.
Instruction for use
Make sure that the 3 R6/AA sized batteries are placed correctly
in the backside compartment of the Wireless Smart-Loader.
Turn the power switch to “on” at the left side of the Wireless
Smart-Loader. A green LED lights up when any button is
pressed, indicating that batteries are in operational condition.
When the red LED lights up, the batteries must be replaced.
Note:
•
Only the
wireless
method can be used for the TV sets
described in this manual.
•
The
wired
method, in which an accessory cable must be
connected between the Wireless Smart-Loader and the TV
set, is
not
an functional option for the TV sets described in
this manual.
Figure 8-1 Wireless Smart-Loader 22AV1120/00
The installation procedure consists of three steps:
1.
Chose the master TV.
2.
Program the Wireless Smart-Loader.
3.
Install TV set(s) of the same type with the Wireless Smart-
Loader. (step 3 can be repeated on as many TV sets as
required).
8.5.2
Choosing a Master TV
The master TV set is the TV whose installation set-up has to be
copied into other TV sets of the same type.
OP4
7
OP_LIP_SYNC
0
0
6
OP_HD
1
1
5
OP_ULTRA_BASS
1
1
4
OP_DELTA_VOLUME
1
1
3
OP_TAIWAN_KOREA
0
0
2
OP_VOLUME_LIMITER
0
0
1
OP_STEREO_DBX
0
0
0
OP_STEREO_NICAM_2CS
1
1
Total DEC Value
113 113
OP5
7
OP_AV1
1
1
6
OP_AV2
1
1
5
OP_AV3
1
1
4
OP_CVI
1
1
3
OP_SVHS2
1
1
2
OP_SVHS3
1
1
1
OP_HOTEL_MODE
0
0
0
OP_SIMPLY_FACTORY =
OP_BTSC_AVSTEREO
0
0
Total DEC Value
252 252
OP6
7
OP_PERSONAL_ZAPPING
0
0
6
OP_SMART_SURF
0
0
5
OP_FMTRAP
0
0
4
OP_COMBFILTER
1
1
3
OP_ACTIVE_CONTROL
1
1
2
OP_VIDEO_TEXT
0
0
1
OP_LIGHT_SENSOR
1
1
0
OP_TWIN_TEXT
1
1
Total DEC Value
27
27
OP7
7
OP_TIME_WIN1
0
0
6
OP_DVB_USB = OP_MALAY
0
0
5
OP_AMBILIGHT
0
0
4
OP_COLUMBUS
1
1
3
OP_DUMMY6
0
0
2
OP_DUMMY7
0
0
1
OP_WEST_EU
1
1
0
OP_MULTI_STANDARD_EUR
1
1
Total DEC Value
19
19
Byte Bit Feature / Mode
32H
F7473/1
0
26H
F5473/1
0
Diversity Storage Byte
Model Address (hex) Diversity code (hex)
26HF5473
0022
16
32HF7473
0022
17
E_14520_077.eps
070806
