Alignments
6.
•
After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE and press OK on the RC.
•
The new option setting is only active after the TV is
switched “off” / “stand-by” and “on” again with the mains
switch (the NVM is then read again).
6.4.2
Option Code Overview
Enter SAM mode to check the option codes. they could be
edited in the NVM.
6.4.3
Display Code Overview
Press the following key sequence on a standard RC
transmitter: “062598” directly followed by MENU and “xxx”,
where “xxx” is a 3 digit decimal value of the panel type: see
column “Display Code” in
. After resetting the Display
Code, restart the set immediately.
Table 6-3 Display code overview
6.5
Reset of Repaired SSB
A very important issue towards a repaired SSB from a Service
repair shop (SSB repair on component level) implies the reset
of the NVM on the SSB.
A repaired SSB in Service should get the service Set type
“00PF0000000000” and Production code “00000000000000”.
Also the virgin bit is to be set. To set all this, you can use the
“NVM editor” and “Dealer options” items in SAM (do not forget
to “store”).
After a repaired SSB has been mounted in the set (set repair
on board level), the type number (CTN) and production code of
the TV has to be set according to the type plate of the set. For
this, you can use the NVM editor in SAM.
In case of a display replacement, reset the “Operation hours
display” to “0”, or to the operation hours of the replacement
display.
Remark:
- After the NVM has been replaced, go to SAM and scroll to the
<Reload MAC address> (see figure 1*).
- Select the item and press <OK> on the RC.
6.5.1
Reset of Repaired SSB
Instruction
After NVM replacement, reload MAC address via SAM
menu.This ensures the correct MAC address to be available in
CSM for future repair actions.
Way of working:
•
After the NVM has been replaced, go to SAM and scroll to
the <Reload MAC address> .
•
Select the item and press <OK> on the RC.
Notes:
•
Only applicable to all related models that are “Smart TV
level 0”enabled (only YouTube access). For models
without internet connection feature, no action is needed.
•
HDCP keys are located in the NVM.
New NVM EEPROMs are shipped with pre-loaded HDCP keys.
6.5.2
SSB Identification
SSB’s of this chassis are identified by a “715” code on the SSB.
715Axxxx-Nnn-MMM-OOOO
•
715 main category, Printed Wiring Board
•
Axxxx sub category, sequential coding number
•
Nnn Version code
•
N Development number
•
nn Production number
•
MMM Mounting variation code
•
OOOO Optional variation code
Make sure when replacing an SSB the SSB identification codes
match the replacement panel.
6.6
Cable position numbers
In this chassis, the cable position numbers can be defined via
the rule that the number is always starting with an “E” followed
by the connector number of the current sourcing board. The
order is always seen from where the power initiates from. So
from PSU to SSB, from SSB to IR/LED panel, from IR/LED
panel to keyboard control panel. For example, a cable from the
PSU connector CN902 to the SSB connector CN701, will have
the position number ECN902.
CTN_ALT BOM#
Panel Type
Display Code
24PFK5211/12
TPM236WF1-HJJP02.N SC4M WH 022
24PFT5211/12
TPM236WF1-HJJP02.N SC4M WH 022
24PFT5211/60
TPM236WF1-HJJP02.N SC4M WH 022
