Philips 237E4QSD/00 Page 49 Service Manual Download

Page: 49 / 75

Meridian 4

14. White Balance, Luminance Adjustment

1. Apparatuses and program:

analyzer CA-210, PC, tool, FGA adjustment program (PhilipsLEDFGA.DDCI),

Pattern generator.

2. Equipment installation:

a. Connect analyzer CA-210 to PC by USB connector, install drive program CA-SDK Ver4.00 for CA-210 and restart

PC after finish installing

b. Install Port95NT drive program, set PC printer connector mode as ECP mode and reset PC after finish installing.

c. Connect tool as follow:

Note: It’s not necessary to connect Port2.

3. Adjustment

Preparation before adjustment:

a. Monitor should be warmed up for more than half an hour.

b. Make sure that the tools are connected right and drive programs have been installed OK.

4. Adjustment process:

a. Press the power of CA-210, shut off the lens, press 0-Cal and open the lens after analyzer reset.

b. Open white balance adjustment program, select the right parameter according with the program and click OK.

c. Make sure that the lens of CA-210 aims at the center of the screen, then click START to adjust.

d. After finish adjusting, the adjustment program displays PASS, and the START button changes for NEXT, which

means that you can adjust another monitor.

To PC LPT

To BSG-265A or
equivalent instrument

To PC Port 2

Philips model

Summary of Contents for 237E4QSD/00












































































Search results

Summary of Contents for 237E4QSD/00

Reviews:

Related manuals for 237E4QSD/00

Brands by name

Popular brands

Philips 237E4QSD/00, Service Manual

Search results

Summary of Contents for 237E4QSD/00

Reviews:

Related manuals for 237E4QSD/00

Brands by name

Popular brands