Philips 22PFS5403/12, Service Manual

Page: 24 / 61

5.2 Error Code
5.2.1 Introduction
Error codes are required to indicate failures in the TV set. In principle a unique error code is available for every:
• Activated (SW) protection.
• Failing I2C device.
• General I2C error.
The last five errors, stored in the NVM, are shown in the Service menu’s. This is called the error buffer.
The error code buffer contains all errors detected since the last time the buffer was erased. The buffer is written from left to right. When an error occurs that
is not yet in the error code buffer, it is displayed at the left side and all other errors shift one position to the right.
An error will be added to the buffer if this error differs from any error in the buffer. The last found error is displayed on the left.
An error with a designated error code never leads to a deadlock situation. It must always be diagnosable (e.g. error buffer via OSD or blinking LED).
In case a failure identified by an error code automatically results in other error codes (cause and effect), only the error code of the MAIN failure is displayed.
5.2.2 How to Read the Error Buffer
You can read the error buffer in below ways:
• On screen via the SAM/CSM (if you have a picture).
Example:
– ERROR: 000 000 000 000 000 : No errors detected
– ERROR: 013 000 000 000 000 : Error code 13 is the last and only detected error
– ERROR: 034 013 000 000 000 : Error code 13 was detected first and error code 34 is the last detected (newest) error
• Via the blinking LED procedure (when you have no picture).
5.2.3 Error codes overview
In this chassis only “layer 2” error codes are available and point to problems on the SSB. They are triggered by LED blinking
when CSM is activated. Only the following layer 2 errors are defined:
D
es
cr
ip
tio
n
LA
Y
E
R
1
e
rr
or
LA
Y
E
R
2
e
rr
or
M
on
ito
re
d
M
ed
iu
m
E
rr
or
/
I²
C
a
d
dr
es
s
E
B
:
in
e
rr
or
b
uf
fe
r
B
L:
B
lin
ki
n
g
LE
D
D
ev
ic
e
D
ef
ec
tiv
e
bo
ar
d
P
ro
t.
I²C BUSSES
I²C 0 (SSB bus) 2 13 SOC I²CM0 E BL/EB SSB SSB
I²C MCU (BE bus) 2 14 SOC I²CMCU E BL/EB SSB SSB
I²C 2 (FE bus) 2 15 SOC I²CM2 E BL/EB SSB SSB
I²C 1 (SFR bus) 2 18 SOC I²CM1 E BL/EB SSB SSB
SOC doesn’t boot (HW
cause)
2 15 St-by µP P D4 BL MT5593 SSB
Supply related:
12V 3 16 St-by µP I/O P BL Supply
Display supply (POK) 3 17 SOC I/O E EB Supply
SSB
I2C switch 2 24 SOC I²CMCU E E0 EB PCA9540 SSB
Channel dec 2 27 SOC I²CM2 E D8-DC EB Silab Si216x SSB
Boston (HDMI2.2) 2 29 SOC I²CM0 E 64 EB SIL 9777 SSB
Lnb controler 2 31 SOC I²CM2 E 10 EB LNBH 25 SSB