background image

Philips Consumer Electronics

Technical Service Data

Service and Quality
Service Publications Dept.
One Philips Drive
P.O. Box 14810
Knoxville, TN 37914

REFER TO SAFETY GUIDELINES

SAFETY NOTICE: ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE
HIMSELF WITH THE CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS
TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.

CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING

© Philips Electronics North America Corporation

Visit our World Wide Web Site at http://www.forceonline.com

Manual 7628

Model no.: 19LT010L/35
First Publish: 12760 S8
Rev. Date: 2002-06-06
Print Date: 13/07/2007

Pg.   SCHEMATIC DIAGRAMS AND PC BOARDS

 1. Chassis Overview
 2. Power Supply [A1]
 3. Line Deflection [A2]
 4. Frame Deflection [A3]
 5. Tuner IF [A4]
 6. Video IF + Sound IF [A5]
 7. Synchronisation [A6]
 8. Control [A7]
 9. Audio Amp Mono Sound Processing [A8]
10. NICAM + 2 CS + BTSC (Stereo/SAP) Decoder [A9]
11. Audio/Video Source Switching [A10]
12. Audio - BTSC Stereo Decoder (Economic) [A11]
13. Front I/O + Front C Headphone [A12]
14. Rear I/O Cinch [A13]
15. CRT Panel [B]
16. SP/LS Event Timer Panel Schematic
17. Side AV Panel [E]
18. Side AV Panel + Headphone [E1]
19. EPS Panel Schematic

20. Card Interface Schematic
21. SP/LS Interface Schematic
22. Healthcare Panel Schematic
23. Layout Mono Carrier Non DBX (component side)
24. Layout Mono Carrier Non DBX (copper side)
25. Layout Mono Carrier DBX (component side)
26. Layout Mono Carrier DBX (copper side)
27. Layout CRT Panel (component side)
28. Layout CRT Panel (copper side)
29. Layout SP/LS Event Timer (component side)
30. Layout SP/LS Event Timer (copper side)
31. Layout Side AV Panel
32. Layout Side AV Panel + Headphone
33. Layout ESP Panel (component side only)
34. Layout Card Interface Panel (component side)
35. Layout Card Interface Panel (copper side)
36. Layout Healthcare Panel (component side)
37. Layout Healthcare Panel (coopper side)

Summary of Contents for 19LT010L/35




































































Reviews: