Philips 107E51/87 Page 27 Service Manual Download

Page: 27 / 81

Electrical Adjustments

Go to cover page

V20 107E5

0. General

8 factory-preset modes

1. This monitor has

as below.

720 x 400 31.5 kHz/70 Hz

640 x 480 31.5 kHz/60 Hz

640 x 480 43.3 kHz/85 Hz

800 x 600 46.9 kHz/75 Hz

800 x 600 53.6 kHz/85 Hz

1.1 14

2. AC/DC Measurement:

The measurements for AC waveform and DC figure is based on 640 x

480 31.5 kHz/60 Hz resolution mode with test pattern "gray scale".

Power input: 110V AC

1280 x 960 60.0 kHz/60 Hz

1024 x 768 68.7 kHz/85 Hz

factory-preload modes as below

640 x 350 31.5 kHz/70 Hz

640 x 350 37.9 kHz/85 Hz

640 x 480 37.5 kHz/75 Hz

640 x 480 37.9 kHz/72.8 Hz

640 x 480 50.6 kHz/100 Hz

720 x 400 37.9 kHz/85 Hz

800 x 600 37.90kHz/60Hz

1280 x 1024 64.0kHz/60Hz

800 x 600 48.1 kHz/72 Hz

800 x 600 63.9 kHz/100 Hz

832 x 624 49.7 kHz/75 Hz

1024 x 768 48.4 kHz/60 Hz

1024 x 768 56.5 kHz/70 Hz

1152 x 864 67.5 kHz/75 Hz

1024x768 60.0 kHz/75 Hz

3.Monitor the following auxiliary voltages.

4.5 Adjust brightness controls to center position except for contrast

control which should be set to MAX.

+5V source across 7153 Pin out and GND

+5V +/- 0.25 VDC

+6.1V source across C2154

+6.1V +/- 0.3 VDC

+12V source across C2155

+12.9V +/- 1.0 VDC

-12V

source across C2156

-12.7V +/- 1.0 VDC

+50V source across C2152

+50V +/- 1.0 VDC

-190V source across C2630

-173V +/- 10.0 VDC

+83V source across C2153 ( + to Gnd)

+76V +/- 2.0 VDC

4. General conditions for alignment

Note: Do not use heatsink as ground.

4.1 During all alignments, supply a distortion free AC mains voltage

to set via an isolating transformer with low internal impedance.

4.2 Align in pre-warmed condition, at least 30 minutes warm-up with

nominal picture brightness.

4.3 Purity, geometry and subsequent alignments should be carried

out in magnetic cage with correct magnetic field.

Northern hemisphere : H=0, V=450 mG, Z=0

Southern hemisphere : H=0, V=-500 mG, Z=0

Equatorial Support

: H=0, V=0

mG, Z=0

4.4 All voltages are to be measured or applied with respect to ground.

5. To access factory mode

To leave factory mode

5.1 Turn off monitor (don't turn off PC)

5.2 Press '"

" and "

" simultaneously on the front control

panel,then press "

",wait till the OSD menu with characters

M32 107E/T4P V1.23 20020426 (below OSD menu)" come on the

screen of monitor.

5.3 If OSD menu disappears on the screen of monitor, press "

again (anytime), then the OSD menu comes on the screen again.

5.4 Using "

" : to select OSD menu.

5.5 Using "

" : to increase or decrease the setting.

5.6 Using "

" to access/confirm the selection.

5.7 After alignment of factory mode, turn off monitor (if you do not

turn off monitor, the OSD menu is always at the factory mode),

then turn on monitor again (at this moment, the OSD menu goes

back to user mode).

MODEL SELECT

Factory

Mode

Indicator

6. Picture geometry setting

- Apply a video signal with cross-hatch pattern.

- Apply a video signal in the 1024 x 768 with 68.7 kHz/85 Hz mode.

- Set contrast control at Max. position, and brightness control in the

mid-point.

6.4 Alignment of horizontal geometry and vertical geometry

6.4.1 Adjust the H-width to 306 mm

6.4.2 Adjust the H-phase to center position.

6.4.3 Adjust V-size to 230mm.

6.4.4 Adjust V-Position to center.

Adjust/Trapezoid/pincushion/balance pincushion/paralleogram

6.4.5 Adjust picture tilt via I C BUS for correct top/bottom lines.

6.4.6 Adjust the top and bottom corner by I C to get optimum

corner geometry.

6.4.7 Adjust the parallelogram by I CBUS to get optimum vertical line.

6.4.8 Adjust the balance pincushion by I C BUS to get optimum

vertical line.

6.4.9 Adjust the trapezoid to get optimum vertical line.

6.5 Adjust size/centering/trapezium/pincushion/parallelogram

of all other preset modes via I C bus.

(to repeat from step 6.4.1 to step 6.4.9)

V20 107E5 V0.20 20021217

http://jdwxzlw.5d6d.com/?fromuser=华盛维修

家电维修资料网，免费下载各种维修资料

Summary of Contents for 107E51/87


















































































Search results

Summary of Contents for 107E51/87

Reviews:

Related manuals for 107E51/87

Brands by name

Popular brands

Philips 107E51/87, Service Manual

Search results

Summary of Contents for 107E51/87

Reviews:

Related manuals for 107E51/87

Brands by name

Popular brands