Philips/Magnavox PM725, User Manual

Page: 7 / 13

13 12
PLAY PLAY PLAY PLAY
STOP STOP STOP STOP REC REC REC REC PAUSE PAUSE PAUSE PAUSE
SCAN SCAN SCAN SCAN+
+ + +
SSSSC C C CA A A AN N N N
PIP
PIP PIP
PIP
TOGGLE
TOGGLE TOGGLE
TOGGLE
LEARN
LEARN LEARN
LEARN
VCR VCR VCR VCR
CBL
CBL CBL
CBL
TV TV TV TV
DVD
DVD DVD
DVD
SAT SAT SAT SAT
PREV PREV PREV PREV
CHAN
CHAN CHAN
CHAN
CODE CODE CODE CODE
SEARCH
SEARCH SEARCH
SEARCH
CD
CD CD
CD
POWER
POWER POWER
POWER
MUTE
MUTE MUTE
MUTE
VVVVOOOOL
LLL ++++
ENTER
ENTER ENTER
ENTER TV/VCR TV/VCR TV/VCR TV/VCR
INFO/
INFO/ INFO/
INFO/
SELECT
SELECT SELECT
SELECT
GUIDE GUIDE GUIDE GUIDE
MENU
MENU MENU
MENU
QUIT QUIT QUIT QUIT
OK OK OK OK
CHAN
CHAN CHAN
CHAN+
+ + +
C C C CH HH HA AA AN N N N
SLEEP SLEEP SLEEP SLEEP
REPEAT REPEAT REPEAT REPEAT
SUBTITLE SUBTITLE SUBTITLE SUBTITLE
C C C CC C C C
+ + + +
CHAPTER CHAPTER CHAPTER CHAPTER
INPUT INPUT INPUT INPUT
AUX AUX AUX AUX
Tips On Learning
1. Use fresh batteries for both the Learning Remote and
the Original Remote.
2. Perform a Master clear (see page 15) before learning.
3. Place the original remote end-to-end with the
Learning Remote so the IR transmitters on both
remotes are directly in line with each other. Keep the
two remotes approximately one inch away from each
other.
4. Experiment by learning 2 or 3 commands initially (to
ensure compatibility and familiarity) and then carry
out a Master Clear before completely learning your
original remote’s commands.
5. Do not try to learn directly under an incandescent or
low-energy light as these can cause interference with
learning. Keep at least three feet away from any such
light sources.
Code Learning
Sleep Timer
The Sleep feature enables the remote to turn off the TV
after a period of 1 to 99 minutes. Remote is to be in TV
mode to set a Sleep Timer. This feature works even if
your TV does not have this feature.
1. Press and release the TV Mode key.
2. Press and hold the Sleep button until LED remains
on (occurring after approx. 2-3 seconds).
3. Release Sleep button.
4. Press and release the numeric keys (01-99) for the
time required. The LED will blink off to indicate
keypress acceptance and remain off after second
keypress.
5. TV Sleep Timer now set.
6. Leave the Remote pointing towards the TV with an
unobstructed path.
To cancel the Sleep Timer, press and hold the Sleep key
until the LED blinks or press and release the Power key
in TV Mode.
Code Identification
1. Press and hold Code Search button until the red
indicator stays on. Release the Code Search button.
2. Press and release the desired mode button (TV, VCR,
etc.).
The red indicator blinks, then stays lit.
3. Press and release the Code Search button. The
indicator light blinks off.
4. To find the first digit for the code stored under the
mode key pressed in step 2, press each numeric key
from 0-9 in turn. When the indicator light blinks off
the number you pressed is the first digit for the code
you are searching for.
5. To find the second digit, repeat step 4, this time
when the indicator light blinks off this is the second
digit.
6. Repeat step 4 again to find the third digit.
Code Identification
1, 3.
2.
4.