8
Press component*
key once (e.g., CBL).
Press SET
until Red Light
blinks twice;
release SET.
Press VOL+ once.
Volume now controlled
through component
selected in step 1.
x 2
1
2
3
* NOTE: Component must have
volume capabilities.
Volume Lock
QUICK FEATURES SETUP GUIDE
This guide is provided here for your convenience as a quick refer-
ence for performing remote control sequences.
Turn on
component
(e.g., TV).
Press component
key once
(e.g., TV).
Press SET
until Red Light
blinks twice;
release SET.
Enter 4-digit code
for your brand;
Red Light blinks
twice after last #.
Press POWER
once; if no
response,
repeat steps
with next code.
x 2
x 2
# # # #
1
2
3
4
5
Component Setup
Turn on
component
(e.g., TV).
Press component
key once
(e.g., TV).
Press SET
until Red Light
blinks twice;
release SET.
Aim remote at
component; press
SCAN once. When
off, press any
key* to stop.
x 2
Press SET
until Red Light
blinks twice;
release SET
to lock code.
x 2
1
2
3
4
5
* NOTE: Not VOL-, LAST, SCAN, or SET.
Auto Scan
Press component
key once
(e.g., TV).
Press SET
until Red Light
blinks twice;
release SET.
Enter 9-9-0;
the Red Light
will blink twice.
Press 1 once for 1st digit.
Wait 3 sec. and count blinks.
Number of blinks equals
value of code digit.
Repeat with 2, 3, and 4.
x 2
x 2
1
2
3
4
Code Verification
Press component key
to be moved once
(e.g.,VCR).
Press SET
until Red Light
blinks twice;
release SET.
x 2
3
Press component key
to be reassigned once
(e.g., AUD). Red Light will
blink twice. Reassigned key is
now ready for programming.
4
1
Enter 9-9-2;
the Red Light
will blink twice.
x 2
2
Device Re-Assignment
(e.g., AUD Key Becomes Secondary VCR Key)
Press and release
SET once. Red
Light blinks twice.
Repeat for up to
10 channels.
x 2
5
Enter channel
Note: Some brands
require ENTER
after channel.
4
Programming The FAV CH Key
Press component
key once
(e.g., TV).
Press SET
until Red Light
blinks twice;
release SET.
Enter 9-9-6;
the Red Light
will blink twice.
x 2
x 2
1
2
3
2.
Press and hold SET until the red light blinks twice, then
release SET.
3.
Enter 9-9-6. The red light will blink twice.
4.
Enter first channel, e.g., 07. For some component brands
the ENTER key must be pressed after the digits, this will
count as a key press. Skip Step 5 if ENTER is needed as
next channel number will be ready to program without
pressing SET.
5.
Press and release SET once (do not hold down). Red
light blinks twice.
6.
Enter second channel, third channel etc. until 10th chan-
nel is reached. Note: If 3 digits plus an Enter is need-
ed for newer TVs/Cable channels, these will not be pro-
grammed. Only 3 entries per channel can be accepted.
7.
FAV CH program exits after 10th channel is pro-
grammed or if SET is pressed for 3 seconds.
8.
Pressing FAV CH key activates the remote to cycle
through the favorite channels every 3 seconds until
favorite channel is locked in by pressing any key.
Note: Favorite channel scan will only work on the component it is
programmed to.
Punch Through
The VCR Transport keys (e.g., REW, PLAY, FFWD, REC, STOP,
AND PAUSE) are set at the factory to control the VCR even if TV
or CBL is the selected mode. In other words,VCR control "punches
through" regardless of what mode is on. Moreover, you do not have to
press VCR before pressing the mode key.
However, if AUD is the selected mode, the VCR Transport Keys will
not control the VCR unless you press the VCR first. In these two
modes, the VCR Transport Keys will operate the functions for the
selected component.
Sleep Feature
Press SLEEP key to activate your component’s internal sleep timer.
(May not be available for all components.) If the component does not
have a sleep function, the first press of the SLEEP key activates the
remote’s built-in sleep timer. Timer can be set to a maximum of 90
minutes.
To Set the Remote’s Built-in Timer
1.
Press SLEEP key once, 15 minute timer is set. Red light
blinks once.
2.
Additional key presses within 10 seconds will increase
the timer value in 15 minute increments up to a maxi-
mum of 90 minutes. For each press of the SLEEP key,
the red light will blink to indicate how many 15 minute
increments have been programmed, e.g., one blink for
first press, two blinks for the second press, etc. Sleep
timer activates 10 seconds after the last press of the
SLEEP key. The red light will blink once every 15 sec-
onds to indicate that the timer is running.
NOTE:
Once the sleep timer is running, the sleep timer is automati-
cally canceled if any other key is pressed. The remote IR must be
pointed to the component to turn off component when timer ends.
To Activate Built-in Sleep Timer if component has
Sleep function
1.
On the remote control, press a component key once
(e.g., TV, VCR,CBL). Sleep feature does not apply
to AUD mode.
2.
Press and hold SET until the red light blinks twice, then
release SET.
3.
Enter 9-7-0. The red light will blink twice.
4.
Follow instructions above to Set Timer.
To reset to component Sleep function follow steps 1
through 3 above. At the end of step three, the red light
will blink four times to indicate the remote is reset to
component Sleep function.
7
