1. Before preparing and stripping the cable ready for connection,
feed the coaxial cable through the hole in the terminal cover.
2. Prepare cable as shown in Fig. 3..
3. Feed prepared cable through the braid clamp and thread the
centre wire through the hole in the central terminal as shown
in Fig. 4.
4. Clamp the cable braid securely fi rst, then tighten the screw on
the central terminal. Trim any stray braid that might come into
contact with the centre wire or central terminal.
5. Replace terminal cover carefully and securely making sure that
the cable is not trapped or kinked.
B. Connecting coaxial cable
CAUTION: When mounting the assembled aerial, always observe
safety precautions and use the correct equipment. Unless you are
competent in the use of ladders and other access equipment, do not
work outdoors at roof height. If in any doubt, refer to a qualifi ed
aerial installer.
braid
centre wire
5mm
10mm
8mm
central
terminal
braid
clamp
C. Coaxial cable routing and
fi xing aerial to a mast
For optimum performance it is very important that the coaxial cable
should be routed as shown in Fig. 5.
DO NOT ALLOW THE CABLE TO TOUCH THE AERIAL
BOOM AT ANY POINT.
PVC insulation tape can be used as shown to hold the cable in place.
1x Central boom: assembly square aluminium (L) approx 865mm
with 7x curved aluminium elements
2x Refl ector booms: Square aluminium (L) approx 160mm with
3x refl ector elements each: curved aluminium (L) approx 425mm
1x Bow tie shaped dipole and printed circuit balun
1x Aerial clamp
Box contents
Mast Clamp
mast
clamp
aerial
boom
PVC
insulation
tape
Coax plug wiring instructions
1 Unscrew coaxial plug housing and slide cap
over cable.
2 Strip 23mm of cable outer sheath.
Gather copper braid, wrap around outer
sheath, slide claw over braid and crimp.
3 Strip 18mm of inner insulation to leave 5mm
exposed
4 Undo screw on plug/clamp, slide clamp over
inner wire & tighten screw. Reassemble plug
1
2
3
4
5
5 Trim inner wire flush with plug.
For best results the aerial should be mounted on an outdoor aerial
mast and pointed in the direction of the nearest transmitter*
making sure it is in a position where the transmitter signal will not
be obstructed by nearby trees and buildings. If you are in any doubt
about the direction in which the aerial should be pointing or the
orientation of the aerial (horizontal for main transmitter, vertical for
relay transmitter) check your neighbours’ aerials.
If mounting on an existing mast check that the mast is in good
condition and fi rmly fi xed.
1. Using the clamp supplied fi x the aerial to the mast - see Fig. 5 & 6.
2. After the aerial direction has been fi ne tuned for best reception
tighten nuts fi rmly until the aerial is securely fi xed to the mast.
Can also be loft mounted.
Fig. 5
Fig. 3
Fig. 4
Fig. 6
Customer Careline:
0901 293 0038
Local rate UK number, Monday to Friday 9am-5pm
Technical Website:
http://technical.philex.com
E-mail Support:
Other Useful Websites for Digital Advice:
*To confi rm that your home is in a coverage area, to fi nd out
what DTT channels should be available locally and to fi nd
out where your nearest transmitter is (distance and compass
bearing) visit: www.dtg.org.uk/retailer/coverage.html
No picture: Check all connections from aerial to TV.
Poor picture: Check all connections from aerial to TV.
Check aerial is properly aligned to the correct transmitter.
If the aerial has been loft mounted try mounting outside.
Make sure new digital coax cable has been used throughout
the installation.
Check the transmitter signal is not obstructed by nearby trees
or buildings.
If in a very weak signal area or for long cable runs, installing a
masthead amplifier will improve the signal.
If in a strong signal area the signal strength may need to be
reduced by fitting an attenuator.
Troubleshooting
PLEASE NOTE: A coax plug is not included with
this aerial. If you need to fi t one please follow the
wiring instructions shown below.
Philex Electronic Ltd 2010.v1.2
www.philex.com
c
