5
[SPECIFICATIONS]
WOOFER
NOMINAL IMPEDANCE
FREQUENCY RESPONSE
RECOMMENDED POWER
EXTERNAL DIMENSIONS
SPEAKER DIMENSIONS
MOUNTING
WEIGHT
GRILLE
ACCESSORIES
(2) 8” Mica-Graphite Polypropylene w/ NBR Surround
4Ω
25 Hz - 160 kHz
350 W Peak
72” H x 14.4” x 3.4” D
20.5” H x 8.75” W
Enclosure mounts between 16” on-center 2” x 4” studded wall
40 lbs. in enclosure
Paintable White Perforated Powder-Coated Galvanized Steel
P350 Amplifier required (sold separately)
IW200 Active Subwoofer
STEP 7:
You are now ready to install the speaker baffle into the mounting flange. An Euro-connector is supplied on the crossover board. This is a two-
piece connector intended to make installation easier. Unplug the male portion of the connector from the circuit board. Insert the positive and negative
conductors of your speaker wire into the screw terminal using care to properly connect the + & - leads correctly. Using a small flat blade screwdriver,
tighten the screws in the connector to secure the wire.
STEP 8:
When mounting the speaker baffle into the flange, pay particular attention to insure the speaker is mounted right side up. The rear panel of the
baffle is marked for correct installation. Optimum performance may only be achieved when the speaker is mounted correctly. Plug the connector into the
crossover observing the correct polarity then install the baffle into the flange assembly. Six screws are supplied to secure the baffle to the flange. Hold
the baffle in position until you have at least two screws properly secured.
STEP 9:
Insert the grille assembly by applying light pressure at each corner of the grill until flush with the flange assembly. A paint shield is supplied with
each grille to protect the drivers in the event the customer wants the grill and flange assembly painted to match the wall color. Once the paint has dried,
remove the grill and the paint shield and re-insert the grille.
NOTE:
A paper clip bent to have a small hook approximately 1/8” long makes a convenient tool
for removing grille without scratching the finish.
[CARING FOR YOUR PHASE TECHNOLOGY SPEAKER]
All Phase Technology speakers are finished with a high degree of craftsmanship in either hand polished paint or vinyl laminates. We recommend using a
lint-free rag with a small amount of glass cleaner to maintain the long-lasting beauty of the finish. Avoid products containing silicones, oils, oil derivatives,
or solvents. Use a damp cloth on enclosures finished in vinyl laminates.
[MAINTENANCE AND SERVICE]
Because of Phase Technology’s uncompromising quality control programs, it’s unlikely that your speakers will ever need service if connected and used
as outlined in this Owners’ Manual. In the unlikely event that a problem does occur, please contact your Phase Technology
®
dealer. Your dealer has the
necessary factory-authorized parts and trained technicians to quickly restore your speaker to its original performance specifications.
[WARRANTY]
LIMITED WARRANTY
:
Phase Technology warrants its loudspeakers to be free from defects in material and workmanship for a period of ten (10) years
for speaker product, limited lifetime for CI speakers, and three (3) years for the electronic components to the original purchaser. Purchase must be made
from an authorized Phase Technology dealer.
This warranty does not cover service or parts to repair damage caused by misuse, abuse, damage while in transit, alterations, unauthorized repairs, failure
to follow instructions, fire, flood or any other cause beyond the reasonable control of Phase Technology. Defects in speaker cabinets or grilles must be
brought to the attention of your dealer immediately after purchase. This warranty will be void if the products’ serial number has been altered or removed.
Should your Phase Technology product require service, please call the MSE Audio customer service department for a return authorization. All merchandise
returned to Phase Technology without prior authorization will be refused. For your return authorization number, please call 855.663.5600 or email sales@
mseaudio.com.
Copyright © 2015 MS Electronics, LLC. All rights reserved. MSE Audio, Phase Technology and PhaseTech are registered trademarks and
“Speakers for your Life” is a trademark of MSE Audio, Overland Park, Kansas USA. Phase Technology is part of MSE Audio
®
. www.phasetech.com.
