4
Copyright © 2015 MS Electronics, LLC. All rights reserved. MSE Audio, Phase Technology and PhaseTech are registered trademarks and
“Speakers for your Life” is a trademark of MSE Audio, Overland Park, Kansas USA. Phase Technology is part of MSE Audio
®
. www.phasetech.com.
[SPECIFICATIONS]
TWEETER
WOOFER
RMS
FREQUENCY
SENSITIVITY
IMPEDANCE
CROSSOVER
DIMENSIONS
CUTOUT DIMENSIONS
MOUNTING DEPTH
WEIGHT
GRILLE
ACCESSORIES
1” Patented Pivoting Woven Synthetic Soft Dome
6.5” RPF
™
Flat-Piston & Kevlar Composite w/ NBR Surround
20 - 150 W
32 Hz - 22 kHz
91 dB
8Ω
2-Way Absolute Phase
™
21.5” H x 10” W x 4.25” D
20.375” H x 8.875” W
4”
21 lbs.
Paintable White Powder-Coated Galvanized Steel
Pre-Construction Bracket (RB-5),CI-FGQM/S Flange & Grille
(extends over edge)
CI110 II
[WARRANTY]
LIMITED WARRANTY
:
Phase Technology warrants its
loudspeakers to be free from defects in material and
workmanship for a period of ten (10) years for speaker
product, limited lifetime for CI speakers, and three (3)
years for the electronic components to the original
purchaser. Purchase must be made from an authorized
Phase Technology dealer.
This warranty does not cover service or parts to repair
damage caused by misuse, abuse, damage while in
transit, alterations, unauthorized repairs, failure to
follow instructions, fire, flood or any other cause beyond
the reasonable control of Phase Technology. Defects
in speaker cabinets or grilles must be brought to the
attention of your dealer immediately after purchase. This
warranty will be void if the products’ serial number has
been altered or removed.
Should your Phase Technology product require service,
please call the MSE Audio customer service department
for a return authorization. All merchandise returned to
Phase Technology without prior authorization will be
refused. For your return authorization number, please call
855.663.5600 or email [email protected].
This is a two-piece connector intended to make installation easier. Unplug the male portion of the connector from the circuit board.
Insert the positive and negative conductors of your speaker wire into the screw terminal using care to properly connect the + & - leads
correctly. Using a 3/32” standard screwdriver, tighten the screws in the connector to secure the wire.
STEP 8:
When mounting the speaker baffle into the flange, pay particular attention to insure the speaker is mounted right side up. The
rear panel of the baffle is marked for correct installation. Optimum performance may only be achieved when the speaker is mounted
correctly. Plug the connector into the crossover observing the correct polarity then install the baffle into the flange assembly. Six screws
are supplied to secure the baffle to the flange. Hold the baffle in position until you have at least two screws properly secured.
STEP 9:
Insert the grille assembly by applying light pressure at each corner of the grill until flush with the flange assembly. A paint
shield is supplied with each grille to protect the drivers in the event the customer wants the grill and flange assembly painted to match
the wall color. Once the paint has dried, remove the paint shield and re-insert the grille.
NOTE:
A paper clip bent to have a small hook
approximately 1/8” long makes a convenient tool for removing CI grilles without scratching the finish.
[CARING FOR YOUR PHASE TECHNOLOGY SPEAKER]
All Phase Technology speakers are finished with a high degree of craftsmanship in either hand polished paint or vinyl laminates. We
recommend using a lint-free rag with a small amount of glass cleaner to maintain the long-lasting beauty of the finish. Avoid products
containing silicones, oils, oil derivatives, or solvents. Use a damp cloth on enclosures finished in vinyl laminates.
[MAINTENANCE AND SERVICE]
Because of Phase Technology’s uncompromising quality control programs, it’s unlikely that your speakers will ever need service if
connected and used as outlined in this Owners’ Manual. In the unlikely event that a problem does occur, please contact your Phase
Technology dealer. Your dealer has the necessary factory-authorized parts and trained technicians to quickly restore your speaker to its
original performance specifications.
218-1107
