Phase Technology TEATRO TSB3.0, Owners Manual/Install Manual

Page: 5 / 9

5
Flat panel display
[FIGURE 2]
STEP 2.1 – WALL MOUNTING
For the best audio experience, the TSB3.0 speaker should be
centrally aligned and mounted directly below the TV display. Each
speaker comes with two identical Mounting Brackets and these
should be mounted to the wall 16 inches apart and centrally
located under the TV.
First, locate the center line of your TV display and make a light
pencil mark on the wall that is 2.5” below the bottom of your
display. Next, measure to the left of this mark exactly 8” and make
another mark at that point. Make sure this mark is also 2.5” below
the TV. Repeat this process on the right side of the display –
making sure that this mark is level with the mark on the left side.
This will create two marks that are 16” apart and 2.5” below the
bottom of your display
(Figure 1) . You have now identified the
location for the two wall brackets for the TSB3.0 speaker.
Using a 1/16” drill bit, drill a pilot hole at each of your two marks
above. Place one of the wall brackets on the wall and align the pilot
hole with the bottom slot on the bracket and drill a second pilot
hole in the center of the upper slot on the bracket
(Figure 2) . This
hole will be 7/8” above the first pilot hole. Repeat this process for
the bracket on the other side. These pilot holes will let you know
if your mounting bracket location is over a wall stud or not. If it is
over a stud then that bracket can be installed with a suitable screw
(for mounting on sheetrock walls, we recommend at least a #10
x 1.5” pan head screw and a flat washer between the screw and
the bracket). If the location for the bracket is not over a wall stud,
then suitable drywall anchors that can support 15 lbs each must
be used.
Following the guidelines above, mount the two brackets to the wall.
Once they are installed check that the center distance between the
vertical mounting slots on the two brackets is exactly 16”. Adjust
the brackets with the horizontal slots until on they are 16” apart.
Locate the two holes on the back of the speaker that are 8”
apart from the center hole and install the two Mounting Pins in
these holes (Figure 3) . Your TSB3.0 speaker is now ready to be
mounted to the wall.
Connect the Left Center and Right inputs from your surround
receiver to the Male Euroblock connectors included with the
speaker. Be careful to observe proper polarity; + (red) on your
receiver to + on the speaker Euroblock connector. Connect the
appropriate Euroblock connector to the left/center/right inputs
on the back of the speaker before placing your speaker on the
Mounting Brackets.
[FIGURE 3]
See step 3 for more detailed information on wiring the TSB3.0.
Gently slide the Mounting Pins into the vertical mounting slots on
the Mounting Brackets. Removal of the flat panel display may be
necessary before mounting the TSB3.0. The Leveling Screws may
be inserted in the bottom of the Mounting Bracket and used to
adjust the height and to make sure the TSB3.0 speaker is level.
Tightening the screw will raise the speaker and loosening it will
lower it.
STEP 2.2 – TABLE TOP MOUNTING
Place your TSB3.0 speaker face down on a soft clean surface
with the grille on. Orient the speaker so the input terminals are
on the right hand side. To attach the Table Top Mounting Feet
to the Mounting Brackets, first remove the Leveling Screws from
the underside of the Mounting Brackets and attach the Table Top
Mounting Feet to the bottom of the bracket using the two supplied
Phillips Table Top Mounting Feet Screws. Make sure that you
orient the feet so that the longer side points to the front of the
TSB3.0
(Figure 4) .
Repeat this for the other Mounting Bracket and Table Top
Mounting Foot. Once you have the Table Top Mounting Feet
securely fastened to the Mounting Brackets, it is now time to
mount them to the TSB3.0. Align the center of the cross section