Phantom Touch n Go Installation Instructions Manual Download Page 18

 

 

 

 

 

 

or it may be contained inside of the plastic portion of the key.    Once again, you can leave the key in the 
factory ignition.    You can also purchase a third party “Factory Security Bypass Module.” These are 
available from manufactures of remote start and alarm systems, and can be found at qualified alarm 
installation shops or online.    They should contain detailed instructions about installation in the 
particular vehicle covered and also the quickest route for disarming the factory alarm.         

Warranty and Legal

 

 

Phantom Products LLC. (“Phantom”) promises to the original purchaser to repair or replace (at 
Phantom’s election) with a comparable reconditioned model any Phantom unit (hereafter the “unit”), 
excluding without limitation remote transmitters, the associated sensors and accessories, which proves 
to be defective in workmanship or material under reasonable use during the first 12 months from the 
date of purchase, provided the following conditions are met: the unit was purchased from an authorized 
Phantom dealer, the unit was professionally installed and serviced; the unit will be professionally 
reinstalled in the vehicle in which it was originally installed; and the unit is returned to Phantom, 
shipping prepaid with a legible copy of the invoice or other dated proof of purchase bearing the 
following information: consumer’s name, telephone number and address; the authorized dealers name, 
telephone number and address; complete product description, including accessories; the year, make 
and model of the vehicle and vehicle engine type. All components including without limitation the 
controller, remote transmitters and the associated sensors and accessories, carry a one-year warranty 
from the date of purchase of the same. ALL PRODUCTS RECEIVED BY PHANTOM FOR WARRANTY REPAIR 
WITHOUT PROOF OF PURCHASE WILL BE DENIED. This warranty is non-transferable and is automatically 
void if: the original purchaser has not completed the warranty card and mailed it within thirty (30) days 
from the date of purchase to the address listed on the card; the unit’s date code or serial number is 
defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended 
purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, 
installation or other causes not arising out of defects in materials or construction. The warranty does not 
cover damage to the unit caused by installation or removal of the unit. Phantom, in its sole discretion, 
will determine what constitutes excessive damage and may refuse the return of any unit with excessive 
damage.   

   

PHANTOM PRODUCTS, IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE 

Summary of Contents for Touch n Go




















Reviews: