Phantom Star ULB44 Installation And Instruction Manual Download Page 6 | Manualshive

Page: 6 / 8

Phantom Star ULB44 Installation And Instruction Manual Download Page 6

-5-

Operating Instructions

The Star Phantom

®

is designed for simple operation using three switches. This unit has

a 3-Way Mode Switch, a Map Light Button, and a Pattern Select/Burst Mode Button.

The 3-Way Mode Switch (Flashing/Off/Steady or Pursuit/Off/Takedown)

This switch is located closest to the driver's side. It is used to select which mode

The

Star Phantom

®

will operate in. While in the Steady (Takedown) mode, the LEDs will

not flash, but instead will remain lit, similar to Takedown lights. Under the Flashing
(Pursuit) mode, the LEDs will flash according to the pattern you have selected (See

Flashing (Pursuit) Mode

below).

The Map Light Button

The button on the left is the Map Light switch. Depressing the button once will
illuminate the "night vision" map light (located at the center of the lightbar). Pressing
the button again will turn the map light off.

Pattern Select/Burst Mode Button

The button to the right of the map light is the Pattern Select/Burst Mode button. This is a
momentary switch and has two different functions, depending upon which mode the 3-Way
Mode Switch is in.

3-Way Mode Switch set for Steady (Takedown) Mode:

If the 3-way mode switch of your

Star Phantom

®

is in the Steady Mode position, the

Pattern Select/Burst Mode will “burst” your LEDs into a super-bright, high-power mode
(takedowns). This mode will activate for approximately 30 seconds then revert to the
standard steady burn mode.

Please Note:

Immediately after the 30 second “Burst Mode” has

ended, the light will be “locked out” of Burst Mode for 30 seconds.

3-Way Mode Switch set for Flashing (Pursuit) Mode:

If the 3-way mode switch of your

Star Phantom

®

is in the Flashing Mode position, the

Pattern Select/Burst Mode button will act as the Pattern Select button. Each time this switch-
button is depressed,

The Star Phantom

®

will cycle to the next pattern.

The Star

Phantom

®

is designed with thirty-five different patterns

(see next page)

.

Indicator LED

Located on the bottom of

The Star Phantom

®

, below the Map Light is an Indicator LED.

When your light is activated in any mode, this LED will flash to alert you to the lightbar activity
in the daylight.

This light may be optionally de-activated if you wish. To do this, while the light is running, hold

down the Pattern Select Button for approximately 12 seconds, until the light flashes 4 times.
This will disable (or enable) the indicator LED.

All wires connected to the positive terminal of the battery should be fused at the
battery for their rated load.

Testing the light before this fuse is properly

installed will void the warranty on the light.

«
...
4
5
6
7
8
»

Summary of Contents for Star ULB44









Reviews:

No comments